Scott Safety MultiFlame FV-40 Series User Manual Download Page 74

Page: 74 / 89

Accessories

FV-40 Series Flame Detector

087-0056 REV F

Notes



The minimum distance from the detector is 30 inches (75 cm).

At extreme temperatures, there is a 15% maximum reduction in the
range.

Important

: Keep the Fire Simulator in a safe place when not in use.

D.1.4

Charging the Battery

Failure to use properly charged batteries could lead to serious injury
or death.

The Fire Simulator uses lithium-ion batteries as a rechargeable power
source. When the batteries are fully charged, the simulator operates for at
least 1000 times without recharging. The simulator will not operate when

the voltage from the batteries is lower than the required operational level.

Figure 14: Flame Simulator Battery Replacement

➣

To charge the battery:

Place the Fire Simulator on a table in a safe area, not exceeding
104°F/40°C.

Release the locking screw.

Unscrew the battery back cover (Item 4) counter clockwise.

Unscrew the locking disc (Item 3) clockwise.

Pull out the battery from the Flame Simulator.

Connect the battery charger. Verify that the charger is the one supplied

with the flame simulator.

Charge for a maximum of 2–3 hours.

Disconnect the charger.

Insert the battery into the flame simulator.

Summary of Contents for MultiFlame FV-40 Series


























































































Search results

Summary of Contents for MultiFlame FV-40 Series

Reviews:

Related manuals for MultiFlame FV-40 Series

Brands by name

Popular brands

Scott Safety MultiFlame FV-40 Series, User Manual

Search results

Summary of Contents for MultiFlame FV-40 Series

Reviews:

Related manuals for MultiFlame FV-40 Series

Brands by name

Popular brands