background image

SYMPTOM

POSSIBLE CAUSE

PROBABLE FIX

No ice compressor is operating

No cooling due to low refrigerant
charge

Locate leak, recover remaining
refrigerant, replace dryer,
evacuate and weigh in nameplate
charge.

Ice is made, but not harvested.

Ice size thermostat contacts do
not switch position

Ice not made near thermostat
probe due to water distributor
holes restricted. Clean water
distributor pan.

Thermostat defective, replace it

Ice will not slide down ice rack
due to minerals on rack.

Clean machine with ice machine
cleaner.

Ice will not slide down ice rack
due to ice rack out of position

Reposition ice rack

Ice will not slide down ice rack
due to bent ice rack

Replace ice rack

Lack of heat during harvest cycle
due to unit in air temp. less than
55

0

F.

Warm up air or move machine.

Lack of heat during harvest due to
water flowing thru water cooled
condenser

Replace water regulating valve

Lack of heat during harvest due to
lack of refrigerant

Check low side pressure during
harvest. If low either the charge is
low or the hot gas valve does not
open fully. If charge is the
problem, locate leak, recover
remaining refrigerant, repair leak,
replace drier, evacuate and weigh
in nameplate charge.

Lack of heat during harvest due to
hot gas valve not opening fully.

Check low side pressure during
harvest. If low either the charge is
low or the hot gas valve does not
open fully.

Ice does not slide down face of
evaporator due to minerals on
evaporator surface

Clean water system with ice
machine cleaner

Harvest cycle too short due to
harvest termination thermostat
opens at too low a temperature.

Replace harvest termination
thermostat

Service Diagnosis: 

SLE300

January 1995

Page 20

Summary of Contents for SLE300

























Reviews: