8
9
When your appliance reacts
,
5
Simply press the ENTER -/-- button and stop the search.
6
To test whether the right setting has been found, simply press
a few buttons on the UFB 3801 and check whether the functions
work correctly. If everything is OK you can now set the UFB 3801
for the second appliance.
The remote control continues the search at the point you stop-
ped It with the
enter
-/--
button. When the end of the code list
is reached the search stops automatically. The remote control
blinks quickly several times. The code last confirmed with the
enter
-/--
remains stored.
If your equipment doesn´t react oder some buttons don´t work,
7
Repeat steps
1
to
6
.
1.2.2 Quick code search
Your remote control finds the correct settings almost auto-
matically in seconds:
1
Switch on the appliance to be controlled.
2
= setuP (3 s)
= set
(LED lights up red)
3
= e.g. tV
= equipment selection
4
= Press once
5
automatic quick search:
The UFB 3801 automatically sends
a different IR code each second. When your appliance reacts,
immediately press the
enter-/--
button to confirm the code.
We advice you to place your finger over the ENTER -/-- button
so that you can react quickly enough. Otherwise the UFB 3801
transmits the next signal before you have reacted.
With very few appliances the quick search does not work. The
search is automatically stopped if there is no reaction from the
appliance to be controlled. You should then use a different set-
ting procedure, e.g. code entry or slow search. Remember to
switch on your appliance again, e.g. DVD, if you wish to continue
the search.
6
Finally, test the set code by controlling e.g. your DVD
appliance. If it doesn´t work correctly repeat steps 1 to 6.
2 general Functions
2.1
Volume Punch-through function:
To simplify operation,
the volume buttons (
VOL►
or
VOL◄
) and the
Mute
button
always control the television set, when VCR and DVD are being
controlled.
2.1.1 Adjustment of ALL volume controls under a specific mode
You can allocate the volume control to one of the modes of the
remote control on condition that the volume control exists on
the corresponding device (e.g. control of TV sound in TV mode,
VCR, DVD).
1
Hold down the
setuP
key until the indicator lamp (LED)
remains lit.
2
Release the
setuP
key.
3
Press the
Mute
key.The lamp flashes once.
4
Press once on the mode key (TV, VCR …) corresponding to the
device whose volume will always be controlled by the VOL and
MUTE keys.
5
Press the
Mute
key once.
2.1.2 adjustment of the volume controls for eacH mode
You can decide that the volume control is functional for each
mode selected on condition that the volume control exists on
the corresponding device (e.g. control of the television set
sound in TV mode, the control of the sound of the SAT receiver
in SAT mode, ...).
1
Hold down the
setuP
key until the indicator lamp (LED)
remains lit.
2
Release the
setuP
key.
3
Press the
Mute
key. The lamp flashes once.
4
Press once on the mode key (TV, VCR, DVD…) corresponding
to the device whose volume will always be controlled by the
VOL and MUTE keys.
5
Press the
VOL◄
key once.
6
Press the
Mute
key once.
2.2 Code identification
1
= setuP (3 s)
= set
(LED lights up red)
2
= e.g. tV
= equipment selection
3
= 1 x
= code search activated
4
1, 2...0
= numerical keys = set
(LED goes out)
The numerical key for which the red LED goes out shortly is the
first number of the code. Press keys
1, 2, 3
to
0
one by one until
the red LED goes out again. This is the second number of the
code. This procedure has to be repeated two times. If the last
number of the code is identified the LED goes out completely.
Now you readout the 4 numbers of this code for this equipment,
e.g.TV.
2.3 2nd operating level
To enter the 2nd operating level press
setuP
1 time
. Now some
keys can be allocated with further functions, e.g.
PROG▲
▼
is
color
+/-
now.
LEITKUFB801_e.indd 8-9
17.06.11 14:26
