manualshive.com logo in svg

SCHUNK EGM B-L-30-1x2, Assembly And Operating Manual

Share
Download
SCHUNK EGM B-L-30-1x2 Assembly And Operating Manual Download Page 32

Assembly

32

01.00 | EGM | Assembly and Operating Manual | en | 389539

5.2.2.2 Turning the connecting plug (EGM B only)

The assembly direction of the connection plug can be modified
with bipolar products. Eight possible connector positions are
available in order to adapt the cable extension to the relevant
installation situation:

Connector positions

CAUTION

Material damage due to turning the connecting plug too far!

The internal wiring can become loose if the connecting plug is
turned by more than 360° compared to its delivery state.

•

Turn the connecting plug no more than 315° as far as
connector position 8.

•

To set a lower connector position, turn the connecting plug in
the opposite direction.

Ø

Loosen both fastening screws of the connecting plug and
remove them.

Ø

Turn the connecting plug to the desired position and insert it.

Ø

Lock the connecting plug with both fastening screws.

Summary of Contents for EGM B-L-30-1x2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands