• 6 •
4.
Ten seconds after the battery has
reached full charge, the green LED
will change from solid to pulsing.
5.
If the Red
Ready/Fail
LED lights and
the buzzer sounds, the unit’s protection
has been activated (such as short
circuit protection, battery low voltage
protection, reverse polarity protection,
etc.) and the unit will not operate.
6.
When the battery is fully charged,
disconnect your charger from the
power source and then remove the
charging cable from the charger and
the unit. Make sure the power switch
is set to OFF, if not using the jump
starter immediately.
6. USING THE JUMP STARTER
JUMP STARTING A VEHICLE
IMPORTANT:
Using the jump starter without
a battery installed in the vehicle will damage
the vehicle’s electrical system.
1.
Turn the ignition OFF.
2.
Lay the DC cables away from any
fan blades, belts, pulleys and other
moving parts.
3.
For a negative-ground vehicle (as
in most vehicles), connect the jump
starter’s POSITIVE (RED) clamp to
the POSITIVE (POS, P, +) battery
post. Next, connect the NEGATIVE
(BLACK) clamp to the vehicle chassis
or engine block, away from the battery.
4.
For a positive-ground vehicle,
connect the jump starter’s NEGATIVE
(BLACK) clamp to the NEGATIVE
(NEG, N, -) battery post. Next,
connect the POSITIVE (RED) clamp
to the vehicle chassis or engine block
away from the battery.
5.
Press the ON/OFF switch to turn the
on the jump starter. The green
Ready
LED will light.
6.
Crank the engine for no more than
8 seconds. If the engine does not start,
wait 2 minutes before cranking again.
7.
After the engine starts, press the ON/
OFF switch to turn the the jump starter
off, and then disconnect the black clamp
(-) and the red clamp (+), in that order.
8.
Recharge the unit as soon as possible
after each use.
USING THE USB PORT
The USB port provides up to 2.4A at 5V DC.
1.
Ensure the battery clamps are securely
clipped on the storage holders.
2.
Press the ON/OFF power switch to
turn the unit ON.
3.
Plug your device into the USB port.
4.
Turn on the USB device.
5.
When finished using the USB port,
turn the switch to the OFF position.
6.
Recharge the unit as soon as possible
after each use.
USING THE WORK LIGHT
1.
Position the jump starter on a flat, stable
surface near the intended work area.
2.
Ensure the battery clamps are securely
clipped on the storage holders.
3.
Press the
Battery Status/Light
button
on the front of the unit for 2 seconds,
to turn on the work light.
4.
When finished using the work light,
press the button for 2 seconds, to turn
off the work light.
5.
Recharge the unit as soon as possible
after each use.
ENERGY SAVING MODE
If the unit is not used after the ON/OFF
power switch is turned on, the unit will go
into Energy Saving mode after 30 seconds,
to prevent battery discharge. Follow these
steps to use any function after Energy
Saving mode:
1.
Press the ON/OFF power switch to
turn the unit ON.
2.
The Green
Ready/Fail
LED will light.
3.
After 30 seconds, The USB port and
Battery Status/Light function will turn off.
4.
After 2 minutes, The Green
Ready/
Fai
l LED will turn off.
5.
Press the
Battery Status/Light
button once. The unit is now ready for
checking the battery status and using
the jump starter, USB and work light.
7. MAINTENANCE AND STORAGE
7.1
Clean the clips and the case each time you
are finished using it.
7.2
Charge battery to full capacity before
storage.
7.3
Store this unit at the temperatures between
-4°F - +140°F (-20 ˚C - +60 ˚C).
7.4
Store clips on their support posts, to
ensure they do not come into contact with
any metallic surface.
7.5
Never completely discharge the internal
battery.
7.6
Charge after each use.
7.7
Charge at least once every month, if not in
frequent use, to prevent over-discharge.
