-7-
-8-
Key operation
Display
Turn the power off
① Hold down PEAK and UNIT key,
② Press POWER key.
Release POWER key only.
4.4.Tracking
A load cell of strain gauge is used for FGJN as a load sensing. By using this sensor, the measuring value is slightly changed due to temperature
and so on, but tracking is able to cancel this slightly change by the software. When you measure very minute forces, measuring value error
might happen due to the tracking. In this case, you may turn off the tracking function.
When the power off, while hold down the PEAK key and UNIT key simultaneously, press and release the POWER key (release the PEAK key and
UNIT key after the value is appeard in the display more than 1 second), you can switch the tracking ON/OFF.
Display force gauge model
J
Tracking OFF
Tracking ON
Standard measuring mode
Please release the PEAK
key and UNIT key after
the value is appeared in
the display more than 1
second.
Tracking ON
Tracking OFF
4.5.Function setting
Key operation
Display
Turn the power off
① Hold down ZERO key,
②
Press POWER key.
Release POWER key only.
Display force gauge model
Display function mode （f01）
Please release the ZERO
key after the value is
appeared in the display
more than 1 second.
The following setting items in function mode.
Item
Unit
Set contents
Default factory setting
Display sign
f01
-0001(minus), 0001 (plus)
0001
Display update time
f02
1、 2、 3、 5、 10、 20 （times/second）
3
Auto power off
f03
10 （10 minutes ）、 oFF （not valid）
10
Turn power off, then press POWER key, you can confirm the condition of
the present tracking.
①
②
①
②
PEAK
ZERO
UNIT
POWER
PEAK
ZERO
UNIT
POWER
PEAK
ZERO
UNIT
POWER
PEAK
ZERO
UNIT
POWER
J
-7-
-8-
4.2.Attaching measuring adapter
Please select the measuring adapter depend on the measuring purpose.
Screw the adapter until it stops lightly. Do not screw it forcibly in order
not to give the damage to the sensor.
Do not use bruised hook or
deformed hook.
Flat head
Cone head
Notched head
Chisel
Extension rod
Hook
PEAK
ZERO
4.Before use
4.1.Charge
Do not charge with non-
attached AC adapter.
Please use AC adapter which supplied with FGJN. If you use non-attached AC
adapter, electronic circuit might be broken and fire might happen.
Before the FGJN arrive at your hand, nickel hydride battery might discharge electricity.
Please plug attached AC adapter and charge before you use.
① Please connect the attached AC adapter into the
AC adapter port
of the
body, and plug them into outlet.
・ Start to charge the Nickel hydride battery. After the completion of the
charge, it stops charging automatically by itself.
・ “BAT” will be shown on the LCD display while charging. After complete the
charging, “BAT” will be disappeared from LCD.
・ Charge time: Up to 16 hours at most
・ Operating time: Approx. 8 hours per 1 full charge
② The nickel hydride battery is charged automatically when it
is discharged during the usage of AC adapter.
※ If you charge the battery frequently, its lifetime will be shorten.
When you use the FGJN with AC adapter, you should not insert and
remove the AC adapter often.
③ You can measure during the charge.
4.3.Attaching hanger
Please take off the attached hanger bolt. Fit the
square hole of hanger into the salient part of the
case, and then tighten the attached hanger bolt.
Please use the hunger to hang the FGJN with
a nail or a winch.
※ Please use the tolerable nail or
winch against the load .
④ When the voltage of nickel hydride battery decline, “LoBAT”
has turned on in the LCD display. Please connect the
AC adapter to charge. (If you leave the FGJN with turned
on “LoBAT” , the voltage decline furthermore, and then the
power
is turned off compulsory.)
Hunger attachement bolt
Hunger
AC adapter port
Please attached the hunger according to need.
Do not screw the attachment
in forcebly.
