manualshive.com logo in svg

Schlumbohm 110 0607, User Manual

Share
Download
Schlumbohm 110 0607 User Manual Download Page 22

Pilot²

 

- 22 - 

3. - 6. Functions Start menu 

 

     

Setup button (see chapter 7) 

 

 

 

 

 

3.  Manual apex length determination 

 

4.  Motor system for NiTi files 

 

5.  BackFill gun DownPack handpiece 

 

6.  Ultrasonic function

 

 

 

 

Battery status display  

 

 

3.  Manual apex length determination 

 

In this menu you can pre-probe the canal manually, i.e. 

with a file guided by the hand. Use the lip clip (4b) and the 

file clamp (4e) for this. 

The marker (horizontal line) determines the position in the 

root canal where the ‘Auto-Stop’  function is reached 

during mechanical preparation. The manufacturer has 

already set the marker. The user (if desired) can, however, 

change the setting directly on the display by moving the 

bar (by tapping on it with the finger). With this function it is 

possible to transfer the X-ray verified position of a pilot 

instrument to the display. 

The marker’s setting remains unchanged until the device 

is switched off. If the device is switched on again, the line 

is reset to the default value. 

 

Do  not  place  the measuring cables on electrically 

conductive surfaces, as external voltages could be 

transferred to the device. 

 

 

Use the          button to access the settings in the Apex setup menu. 

 

 

 

 

 

 

 

Summary of Contents for 110 0607













































Reviews:

No comments

Brands by name

Popular brands

Load more brands