3 • Schlage • CT5000 user guide
Overview
The Schlage CT5000 is an off-line access controller in the AD-Series product line.
• The CT5000 is intended for use on one (1) single opening.
• May be used with up to two (2) credential reader interfaces that use Wiegand and/or
Clock & Data outputs.
• Externally powered using a UL294 power supply for UL installations and a ULCS318/
ULCS319 listed Class 2 power supply for cUL installations (not included) capable of
sourcing at least 500 mA @ 12 or 24 VDC (example: Schlage models PS902, PS904,
PS906).
• Capable of storing credentials for up to 5000 users.
• Maintains an audit trail of up to 5000 events.
• Intended for indoor use only. Ambient temperature range -35C to +66C (-31F to +151F).
• The CT5000 is configured using the Handheld Device (HHD). See
Handheld Device
(HHD)
on page 14 for more information.
• Any installation involving an opening which is considered an emergency exit or a fire
rated opening must conform to all local and national safety and building codes.
• Access equipment manufactured and/or sold by Allegion is not rated for, or intended
for use in life safety installations. UL listed panic hardware must be used to allow
emergency exit from the protected area.
•
Before installing the CT5000 controller, read all documentation for all products in
the installation
.
+
-
+
-
C
B+
1
+
+
1
1
GND
GND
IF RADIO BOARD PRESENT
NC
BATT
COIN CELL NOT NEEDED
NC
C
NO
C
NO
PRIMARY SIDE
BEEPER
BEEPER
ALARM
STRIKE
AUX
PWR/
SIDE UP
LINE
GND
RT
E
GND
GND
1
1
1
1
RED
GRN
GND
DA
TA\D0
CLK\D1
GND
SWITCH INPUT
CLK\D1
DA
TA\D0
RED
GRN
READER1
READER2
TAMP2
TAMP1
DPS
RT
X
GND
DEBUG
TAMPER
STATUS
RELAY
RX/TX
USB
+12V
+5V
LID
+3.3V
RX
TX
GND
OPEN
A-
1
1
1
1
1
1
1
1
23394075_C
SCHLAGE
LINK
RESET
TAMPER
GND
ICLK
IDAT
RB8
RB7
GND
VDD
MCLR
USB
AA
BATT
LINE
ALR_NC
ALR_C
ALR_NO
AUX
AUX
AUX
STR
STR
STR
RB+
TB+
TA
-
RS485
12/24VDC
THIS
MOUNT
LED2
BATTERY_HOLDER1
R1
12 C61
U4
REL1
J3
J7
REL2
REL3
U5
TP25
TP24
TP23
TP22
TP21
J6
LED1
LED4
LED7
LED5
LED6
LED3
J18
J17
J13
LED8 LED9
C32
J9
J12
J11
J10
J8
S3
S2
S1
J5
J2
J1
J2
Lid Tamper
Switch Input
J13
Switch Inputs
J10
Reserved
J5
USB
J7, Power
12 or 24 VDC
J17
Reader 1
J18
Reader 2
J6
Relay Outputs
SW1
Lid Tamper
Switch
Mounting
Hole
Mounting
Hole
Mounting
Holes
J8
6” (15.25 cm)
9
⁷⁄₈
”
(25.25 cm)
