www.scheppach.com
+(49)-08223-4002-99
+(49)-08223-4002-58
14 |
14 | GB
Device description (Fig. 1-8)
1. Transport handle
2. Pressure switch
3. Pressure regulator
4. Quick-lock coupling (regulated compressed air)
5. Pressure gauge (for reading the preset vessel
pressure)
6. Pressure gauge (for reading the vessel pres-
sure)
7. Pressure vessel
8. Supporting foot
9. Wheel hub bolt
10. Wheel
11. Pressure pipe
12. Crankcase
13. Oil plug
14.
Air filter
15. Drain plug for condensation water
16. Safety valve
17. ON/OFF switch
18. Oil level / -control display
19. Oil drain plug / screw
20. Overload / protection switch
Scope of delivery
•
Open the packaging and remove the device care-
fully.
•
Remove the packaging material as well as the
packaging and transport bracing (if available).
•
Check that the delivery is complete.
•
Check the device and accessory parts for trans-
port damage.
•
If possible, store the packaging until the warranty
period has expired.
m
ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
Intended use
The compressor is designed to generate com-
pressed air for compressed-air driven tools which
can be driven with an air volume of up to approx.
200 l/min
(e.g. tire infl ator, blow-out pistol and paint
spray gun).
Due to the limited air output it is not possible to use
the compressor to drive tools with very high air con-
sumption (for example orbital sanders, rod grinders
and hammer screwdrivers).
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufac-
turer will be liable for any damage or injuries of any
kind caused as a result of this.
Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
•
Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
WE RECOMMEND:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before op-
erating the machine and carefully follow its informa-
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associated
dangers. The minimum age requirement must be
complied with.
In addition to the safety notices contained in this
operating manual and the particular instructions for
your country, the generally recognised technical reg-
ulations for the operation of identical devices must
be complied with.
