Schenker MODULAR 500 Installation, Use And Maintenance Manual Download | Manualshive

Page: 28 / 57

background image

4

– MOUNTING AND INSTALLATION

COD:

500M380.D.2018

EN

THE PRESENT MANUAL BELONGS TO -

Schenker Italia

- ALL RIGHTS RESERVED

28

4.5 Electric connections

ATTENTION

These steps have to be performed by a qualified technician/operator, by referring to the
electrical drawings provided within this document.

4.5.1

Remote control panel mounting

The remote control panel has the following dimensions:

width 135 mm.

height 116 mm.

It can be fixed on any internal vessel panel, provided that the area behind is free of humidity and condensation
and there is enough depth to house the rear part of the panel (approx. 8 cm.).

The cut to be performed on the vessel covering panel, to encase the remote control panel, has the following
dimensions:

width 115 mm. height 97 mm.

The remote control panel can be connected through the pre-wired multiple cable of a 10mt standard length
provided. It is possible to adapt the panel to a longer distance by adding a one more cable in series to the one
provided.

REMOTE CONTROL PANEL

FIG. 4-3

Fresh water connection

To be connected to the

tank of the vessel

«
...
26
27
28
29
30
...
»

Summary of Contents for MODULAR 500


























































Reviews:

No comments

Related manuals for MODULAR 500

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 2

SCHT680 - RECEIVER W/5-DISK DV

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 52

SCBT235 - BLU RAY HOME THEATER SYSTEM

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 26

SCBT228 - BLU-RAY HOME THEATER-EASY

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 112

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 32

Brand: DAS Pages: 6

Brand: Samson Pages: 8

Brand: Eaton Pages: 29

Brand: EAW Pages: 2

Brand: EAW Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands