www.scarlett-europe.com
SC-446
5
GB
INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
·
Before the first connecting of the appliance check that voltage indicated on the rating label corresponds to the mains voltage in your home.
·
For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual.
·
Do not use outdoors.
·
Always unplug the appliance from the power supply before cleaning and when not in use.
·
To prevent risk of electric shock and fire, do not immerse the appliance in water or in any other liquids.
·
Close supervision is necessary when it is used near children or invalids.
·
Do not leave the appliance switched on when not in use.
·
Do not use other attachments than those supplied.
·
Do not operate after malfunction or cord damage.
·
Do not attempt to repair, adjust or replace parts in the appliance. Check and repair the malfunctioning appliance in the nearest service center only.
·
Keep the cord away from sharp edges and hot surfaces.
·
Do not pull, twist, or wrap the power cord around appliance.
·
Never attempt to take food or liquid out from the container when the blade is moving. Always wait until the motor stops completely.
·
Do not overload the appliance with food.
·
The appliance operates fast and effective.
Do not operate continuously for more than 1 min
.
·
Never place hot ingredients into processor (> 70 ºC)
.
FOOD PROCESSOR ASSEMBLING
·
Before the first using, wash all removable parts in warm soapy water, rinse thoroughly and dry. Wipe the housing with a damp cloth.
·
Never immerse motor body in any liquid or wash under running water.
·
Place the motor unit on a level surface.
ATTENTION:
Never operate processor bowl and blender at the same time.
·
Place the bowl on the motor unit.
·
Place blender gear safety lid on the seat, rotating until fixed securely.
ATTACHMENTS
·
Use
ONLY ONE
attachment for food processing.
CUTTING KNIFE\PLASTIC BLADE
·
Fit shaft adaptor into the blade (or whip maker) until it fixed securely.
·
Fit shaft adaptor on the bowl drive spindle.
·
Load products to be processed in the bowl.
·
Place lid on the bowl and rotate it to lock.
·
Turn bowl clockwise to the proper position
·
Start processing at high speed (position
).
DISKS - GRATING / SLICING / SHREDDING
·
Set the slicer, grater or shredder knife in the supporting disc and place it onto shaft adaptor.
·
Fit the disk with the spindle onto the blender shaft.
NOTE:
you must complete assembling fully; otherwise you cannot switch on device.
FOOD PROCESSOR USING
·
Please make sure accessories are at its places before switching on.
·
Plug-in device.
PULSE MODE
It is provided two ways of turning on a pulse mode
-
Turn the Speeds control switch to
position.
-
Press and retain the Pulse button - food processor will operate till this button is pressed.
·
Before processing cut a food so it would pass through a feeder easily.
·
Turn control switch to speed "1" (low speed) or "2" (high speed), so food processor will work continuously until you turn back to "0" (switch off).
·
Gradually feed products to be processed through the feed tube
only while processor is operating
.
CAUTION:
Use the pusher only to feed products, push it evenly and gently. The heavier pressure, the coarser chopping.
CAUTION:
Do not operate continuously longer than 1 minutes with less than 1 minute intermission
.
·
Do not overload the appliance by putting in too much food.
·
Do not remove any parts during the operating.
BLENDER
·
Leave the processor bowl at the place locked into the slot. Remove shaft adaptor and attachments; do not place food in the processor bowl.
·
Open blender gear safety cap.
·
Place the blender jug onto the blender gear. Make sure it properly fitted.
·
Put ingredients into blender jar, and close it with the lid.
·
Plug-in, turn the switch/press buttons to recommended speed:
"1"(low speed) for liquid ingredients mainly.
"2" (high speed) for heavier processing, i.e. liquid and solid ingredients mixtures.
The appliance will operate until it will be switched off.
- PULSE mode.
·
Blender could process fruit juices, ice-cocktail, etc.
CITRUS PRESS SET
·
Place the strainer on the bowl then turn the handle until it locks into the bowl lid-locking slot.
·
Place the cone into the hole in the strainer.
·
Press on a half of a fruit to the cone.
·
Turn Speeds control switch to
(slow speed) to start the appliance. For greater control use the Pulse mode.
CAUTIONS:
·
Avoid operating the empty blender;
·
Never place hot ingredients into blender jar (> 70 ºC);
·
Ingredients must be cut into small pieces before processing in blender jar;
·
Never fill blender jar with a liquid over maximum level marked;
·
When processing is finished, switch off, and then unplug the appliance and wait the motor will stop before removing a food and attachments.
CLEANING AND CARE
·
Switch off and unplug the appliance.
·
Wash the accessories immediately and avoid soaking them in water for long periods; wash in warm sudsy water after each use. Dry all accessories
with a clean soft cloth.
·
Wipe housing with a damp cloth.
·
Do not use scouring pads, abrasive and harsh detergents.
CLEANING THE BLENDER JUG
·
Place empty blender jug onto the motor unit and cover with the lid.
