IM003
www.scarlett.ru
SC-1265
5
GB
INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
•
Please read this instruction manual carefully before use and keep in a safe place for future reference.
•
Before the first use of the appliance check that voltage indicated on the rating label corresponds to the mains
voltage in your home.
•
For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than
described in this instruction manual.
•
Do not use outdoors.
•
Always unplug the appliance from the power supply before cleaning and when not in use.
•
To prevent risk of electric shock and fire, do not immerse the appliance in water or any other liquids. If it has
happened DO NOT TOUCH the appliance, unplug it immediately and check in a service center.
•
Do not take this product to a bathroom or use near water.
•
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliances by a person responsible for their safety.
•
Children should be supervised to ensure that they do not play with the appliance.
•
Do not leave the appliance switched on when not in use.
•
Do not use other attachments than those supplied.
•
Do not operate after malfunction or cord damage.
•
Do not attempt to repair, adjust or replace any parts of the appliance. Check and repair the malfunctioning
appliance in the nearest service center only.
•
Keep the cord away from sharp edges and hot surfaces.
•
Do not place or store the appliance where it can fall or be pulled into a tub or sink.
•
Do not pull, twist, or wrap the power cord around the appliance.
•
Never insert any objects into openings in the appliance housing.
•
Before use, make sure that blades are adjusted properly.
•
Do not put operating appliance on any surface, it may cause injury or damage.
•
Do not use the appliance with damaged comb, or with teeth missing from the blades as injury may occur.
NOTE:
KEEP THE BLADES OILED.
•
Do not use the hair clipper when the skin is infected.
•
Do not use the hair clipper on animals.
BLADE ALIGNMENT
•
Your clipper was carefully examined to ensure that the blades were oiled and properly aligned before leaving our
factory.
•
Blades must be realigned if they were removed for cleaning or after replacement.
•
To realign the blades, simply match the upper and lower blades teeth up, point for point.
•
End of top blade teeth should be approximately 1.2 mm back from lower blade. Compare your clipper blades with
the sketch (pic.1).
•
If blade alignment is incorrect, add a few drops of oil to the blades, switch on the clipper for a few moments,
switch off and unplug. Loosen screws slightly and adjust. Tighten screws after blade is aligned.
OILING
•
To maintain your clipper in peak condition, the blades should be oiled after every haircut.
•
Do not use hair oil, grease, oil mixed with kerosene or any solvent.
BLADE LEVER
•
The lever located to the left of the blades, allows easily adjust cut hair length while
clipping.
•
The lever adds versatility to your clipper by allowing you gradually change the closeness
of your cut without an attachment comb.
•
When the lever is in the uppermost position, the blades will give you the closest cut and
leave the hair very short. Pushing the lever downwards gradually increases the cutting
length.
•
In its lowest position, the lever will leave the hair approximately the same length as a
№
1 (3mm) comb.
•
The lever will also extend the use of your blades since a different cutting edge is used in each setting.
•
In addition, if extremely heavy hair cutting has jammed the blades, it will help you to remove hair that has
become wedged between the two blades without removing the blades.
•
While the clipper is running rapidly move the lever from “close cut” to “longer cut” a couple of times. Do this each
time after you have finished using your clipper to keep the blades free of cut hair.
•
If this does not help and clipper stops cutting, blades are dulled. Replace them with new blades.
INSTRUCTIONS FOR HAIR CUTTING
•
Before starting the hair cut inspect the clipper, making sure that there is no oil between the cutting blade teeth,
switch the unit on to distribute the oil between the blade teeth and to check running smoothness. Wipe off any
excess oil. This should be done after each use. While using the unit, untwist the cord from time to time to avoid
tangling.
•
Before cutting always comb the hair thoroughly first.
