background image

 

                                                                                                    

COMPACT 110

 

 

COMPACT 110  

Operator’s manual for drilling machine   

 

 

- 17 - 

a)  Stopping the motor is executed with red button „O” (02) (the motor is switched OFF but 

the electromagnetic base is still ON) (02). 

b)  Blinking of the red LED overload indicator (03) means that the machine is working at the 

limit of the overload. The machine can be automatically turned off at any time. 

c)  To change the rpm speeds machine use the shift lever (04)  

       

 

To move machine into next drilling spot, stop the motor as described above then 

push switch MAGNET into the position “O”.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

III. MAINTENANCE AND SERVICE 

 

To avoid accidents drill stand, power cable, wiring, plug connectors, switches must be 

regularly inspected for damage. 

  

 

  Perform adjustment of the machine play guides every 50 hours or as necessary 

performed by the regulation screws. Slide guide loose is correct if the drive can be 
moved smoothly by  using  the lever.  It’s  not accepted  to automatically  slide down 
under its own weight. (see II point 2.9) 

  Due to the distribution of lubricant after every days work position of gear lever (used 

for selection of gearbox speed) should be changed. For example if machine worked 
with 150 rpm speed, it should be switched to 300rpm. (see IV point.1). 

  Every 250 hours of work check condition of carbon brushes. If their length is less than 

5 mm they should be replaced for original new ones. After replacement new brushes 
should be run-in without load for about 20 min. Other repair work should be done only 
by authorized service points, appointed by distributor. Replacement of brushes is 
possible without removal motor unit from the unit.  (see IV) 

  Lubricate regularly brass slide guide inserts with grease as well as the rack and    

pinion. 

Drawing No.6 Control  Panel 

Drawing No.7  View of the machine COMPACT 

110 

(01) 

(03) 

(02) 

Summary of Contents for COMPACT 110






































Reviews: