12
BEFORE INSTALLING THE APPLIANCE
Before connecting your appliance to the power supply, check that
the voltage stated on the rating label of your appliance corre-
sponds to the voltage in your home. A different voltage could
damage the appliance.
The plug is the only way to unplug the appliance and should
therefore be accessible at all times. To turn off main power to the
appliance, turn it off and then detach the plug from the outlet.
The appliance must be grounded. The manufacturer is not re-
sponsible for damages that may occur as a result of usage wit-
hout grounding.
INSTALLATION
Install the appliance in a dry, well ventilated room. The instal-
lation location should neither be exposed to direct sunlight nor
near a heat source, e.g. a cooker, radiator, etc.
To ensure adequate ventilation for the appliance, allow a mini-
mum of 10 cm of airspace on each side of the cabinet.
For uneven surfaces, front feet can be aligned.
AMBIENT TEMPERATURE
This appliance is designed to operate in ambient temperature
between 10°C and 38 °C. If these temperatures are exceeded,
i.e. colder or warmer, the appliance will not operate correctly.
If the ambient temperatures are exceeded for long periods, the
temperature in the freezer compartment will rise above -18°C
and food spoilage may occur.
BEFORE PLACING FOOD IN THE APPLIANCE
• Remove all packaging.
• Allow the appliance to run empty for 2 – 3 hours so the
compartments can cool to the appropriate temperature.
• Clean the inside of the appliance with warm water and a lit-
tle liquid detergent to remove manufacturing and transpor-
tation dust.
POWER FAILURE
If there is a power failure, do not open the fridge door. Frozen
food should not be affected if the power failure lasts for less than
21 hours.
Do not refreeze frozen foods that have thawed completely. The
food may be dangerous to eat.
ADJUSTING THE TEMPERATURES AND FUNC-
TIONS
• After the appliance is plugged into the mains socket, the
display will illuminate.
The
”smart ECO” function will be activated and the indicator
light
”smart ECO” will illuminate for a while.
• When display indicator lights go out, open the fridge door or
press any button and then the indicator lights will illuminate
again.
Setting the temperatures of fridge and freezer compartments
Make sure the
”smart ECO” function is cancelled (see the in-
struction on how to cancel the
”smart ECO” function in the sec-
tion of
”smart ECO” below).
1 To set the temperatures, press Fridge / Freezer once.
• The temperature will flash on the display.
2 While the temperature is flashing, repeatedly press Fridge /
Freezer to select the desired temperature.
• The temperature of the fridge compartment can set be-
tween 2°C and 8°C.
• The temperature of the freezer compartment can be set
between -24°C and -16°C.
3. Press OK to confirm.
• If no button is pressed within 5 seconds, the temperature
will stop flashing, indicating the temperature is set.
• When the fridge compartment is set to the
“OFF” setting,
the fridge compartment will stop cooling.
Smart ECO
1 Repeatedly press Function until the corresponding indicator
light
”smart ECO” flashes on the display.
2 While the indicator light is flashing, press OK to confirm.
• The light will stop flashing, indicating the
”smart ECO”
function is activated.
• The temperatures in the fridge and freezer compartments
will be 4°C and -18°C respectively.
NOTE: The temperatures cannot be adjusted when the function
is activated.
To cancel this function
1 Repeatedly press Function until the smart ECO indicator light
is flashing on the display.
2 While the indicator light is flashing, press OK.
• The indicator light will go out.
• The temperatures will return to the previous settings.
Fast cooling
The
”fast cooling” function can be used to rapidly reduce the
temperature in the fridge compartment to its lowest setting.
It is recommended to use this function for the faster chilling of
large amounts of fresh food or drink.
1 Repeatedly press Function until the corresponding indicator
light
”fast cooling” flashes on the display.
2 While the indicator light is flashing, press OK to confirm.
• The indicator light will stop flashing, indicating the
”fast
cooling” function is activated.
• The temperature of the fridge compartment will be 2°C
and cannot be adjusted.