background image

1

R

Section 1

1.1 INTRODUCTION

This manual has been prepared to provide the    
information you need to correctly assemble, operate, and 
maintain this grass catcher.  Read it carefully and keep it 
for future reference.

THE REPLACEMENT OF ANY PART ON THIS PRODUCT 
BY OTHER THAN THE MANUFACTURER'S AUTHORIZED 
REPLACEMENT PART MAY ADVERSELY AFFECT THE 
PERFORMANCE, DURABILITY OR SAFETY OF THIS 
PRODUCT.

USE OF OTHER  THAN ORIGINAL SCAG REPLACEMENT 
PARTS WILL VOID THE WARRANTY.

If additional information or service is needed that is not 
outlined in this manual, please contact your Scag Power 
Equipment dealer.  Scag dealers are trained in the latest 
service methods and carry a full line of Scag replacement 
parts.

When ordering parts, always provide the complete model 
number and serial number of your catcher.

All  information  provided  in  this  manual  is  based  upon 
information available at the time of printing.  Scag Power 
Equipment reserves the right to make changes at any time 
without notice or obligation.

1.2 DIRECTION REFERENCE

The “Right” and “Left”, “Front” and “Rear” of the machine are 
referenced from the operator’s right and left when seated 
in  the  normal  operating  position  and  facing  the  forward 
travel direction.

1.3 SAFETY AND OPERATING 
INSTRUCTIONS

 NOTE -

To avoid personal injury, it is imperative that all 
safety instructions be observed.

1.  Read this operator's manual and the operator's 

manual that is supplied with the machine this 
attachment is used on.

GENERAL INFORMATION

A replacement manual is available from your authorized 
Scag  Service  Dealer  or  by  contacting:    Scag  Power 
Equipment, Service Department at P.O. Box 152, Mayville, 
WI 53050.  You may also contact us through our website at 
www.scag.com  The manual for this grass catcher can be 
downloaded by using the model and serial number or use 
the contact form to make your request.  Please indicate the 
complete model and serial number of your Scag product 
when requesting replacement manuals.

 WARNING

Do not operate without discharge chute, mulch 
kit, or entire grass catcher installed.

2.  Before removing the grass bags, disengage the 

mower, stop the engine and wait for all movement to 
stop.

3.  ALWAYS

 turn the engine 

OFF

, remove the key and 

wait for all movement to stop before servicing or 
cleaning the mower or the grass catcher.

DANGER

ROTATING BLOWER

BLADES

STOP ENGINE BEFORE

ENTERING CHUTE

CONTACT CAN INJURE

4.  Do not modify or alter any component of the grass 

catcher attachment or mower.

5.  Do not allow any passengers to ride on the grass 

catcher attachment or on the mower.

Summary of Contents for GC-2B


























Reviews: