sauter RDT 921 F901 Hardware Manual Download Page 11

Page: 11 / 38

Sauter Italia S.p.A.

RDT921F901

| Hardware manual ver. 1.0 | Code 114RDT921E104SAU

page 11 of 38

DIGITAL OUTPUTS

Digital outputs.

PART

MEANING

CO1

common digital output 1

NO1

usually open contact for digital output 1

according to model:

electromechanical relay with 3 A res. @ 250 VAC

control for 24 VAC/DC, 600 mA max. solid state relays

CO2

common digital output 1

NO2

usually open contact for digital output 2

according to model:

electromechanical relay with 3 A res. @ 250 VAC

control for 24 VAC/DC, 600 mA max. solid state relays

CO3-6

common digital output 3... 6

NO3

usually open contact for digital output 3 (electromechanical relay with 3 A res. @ 250 VAC)

NO4

usually open contact for digital output 4 (electromechanical relay with 3 A res. @ 250 VAC)

NO5

usually open contact for digital output 5 (electromechanical relay with 3 A res. @ 250 VAC)

NO6

usually open contact for digital output 6 (electromechanical relay with 3 A res. @ 250 VAC)

CO7

common digital output 7

NO7

usually open contact for digital output 7 (electromechanical relay with 3 A res. @ 250 VAC)

NC7

usually open contact for digital output 7

CAN/RS-485

RS-485 MODBUS slave, RS-485 MODBUS master/slave and CAN CANBUS ports

The communication protocol for the RS-485 MODBUS master/slave port can be set with the development environment.

For the settings for the RS-485 MODBUS slave, RS-485 MODBUS master/slave and CAN CANBUS ports, please refer to chapter 6

“CONFIGURATION”.

PART

MEANING

CAN+

CAN CANBUS port positive pole

CAN-

CAN CANBUS port negative pole

GND

RS-485 MODBUS slave, RS-485 MODBUS master/slave and CAN CANBUS ports ground

A1/+

RS-485 MODBUS master/slave port positive pole

Summary of Contents for RDT 921 F901







































Search results

Summary of Contents for RDT 921 F901

Reviews:

Related manuals for RDT 921 F901

Brands by name

Popular brands

sauter RDT 921 F901, Hardware Manual

Search results

Summary of Contents for RDT 921 F901

Reviews:

Related manuals for RDT 921 F901

Brands by name

Popular brands