sauter HK-D Instruction Manual Download | Manualshive

Page: 18 / 33

background image

18

HK-D_HK-DB-BA-e-2020

The buzzer leaves a long beep if the value is not within the tolerance limit. When the
preset number of rebounds has been reached, two short beeps will sound. After 2
seconds a short signal tone sounds and the average value is displayed.

Key function

- Use the key

【

SAVE

】

wird to store the current measuring group in the memory. This

operation can only be carried out after the average value has appeared on the display.
In addition, this memory function can also be executed only once.

- With the key

【

DEL

】

wird the last single value is deleted. When this key is pressed,

the following appears on the display:

- - - - - - - - - - - - -
Confirm delete?
- - - - - - - - - - - - -
YES NO

- Pressing or

key will move

the cursor to nach

【

YES

】

bewegt. Use the key

【

ENTER

】

wird to confirm the deletion of the last individual measured value.

- Press the or

key to move the cursor to nach

【

NO

】

bewegt. Pressing the key

【

ENTER

】

wird cancels the deletion. Deleting can also be cancelled by pressing

【

ESC

】

abgebrochen wherever the cursor is located.

- Use the keys

【】

und

【】

wird to display the individual measured value. The

average value or the last measured value can be displayed again by pressing the

【

ESC

】

aufgezeigt key. The viewing sequence varies depending on the

【

】

oder

key.

- Press the key

【

AVG

】

kann to end the test, even if the preset rebound number has

not yet been reached, and the average value calculated from this is displayed.

- Use the key

【】

wird to switch the LCD backlight on or off.

- Press the key

【

MENU

】

oder

【

ENTER

】

gelangt to enter the main menu of the

system.

Preset of the shortcut keys:

- Use the

【

DIREC

】

wird key to set the direction of the rebound sensor.

- Use the key

【

TIMES

】

wird to change the number of rebounds in a measuring

group. The current number of rebounds can be changed by first pressing the key

【

TIMES

】

angezeigt. Each time the Taste

【

TIMES

】

erhöht key is pressed again, the

number of rebounds increases by plus one. The value jumps back to 1 when the
number of rebounds reaches 32.

- Change the hardness scale with the key

【

HARD

】

wird. Whenever this button is

pressed, a continuous conversion takes place under all existing hardness scales which
are available for the material currently under test and the corresponding rebound

«
...
16
17
18
19
20
...
»

Summary of Contents for HK-D


































Reviews:

No comments

Related manuals for HK-D

Brand: Parr Instrument Pages: 110

Brand: Keithley Pages: 201

Brand: Hameg Pages: 44

Brand: Hameg Pages: 60

Brand: Hameg Pages: 28

Brand: HAMAR LASER Pages: 113

Brand: Jasco Pages: 48

Brand: TC Electronic Pages: 20

Brand: E Instruments Pages: 144

Level Pro UltraPro 500 Series

Brand: Icon Process Controls Pages: 19

DIRIS Digiware D-40

Brand: socomec Pages: 58

Brand: Axio MET Pages: 5

PRO VPR100 Series

Brand: CTC Union Pages: 10

Brand: PCB Piezotronics Pages: 15

Brand: Sercel Pages: 63

Brand: M & I Instruments Pages: 3

Smart Air Quality Monitor

Brand: Lennox Pages: 28

Brand: Roland Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands