19
V_SC_5109NC_202104
2. Installation of shield and wheel (Figure C)
WARNING
The cut-off wheel is equipped with a fully-closed shield
and the grinding wheel blade is equipped with a semi-
closed shield. Moreover, the diameter of wheel shall
match that of shield.
Installation or removal of shield (see Figure D)
WARNING
When the tool is used, the shield shall be mounted on
the tool and the closed side of shield shall always face
the operator!
Installation of shield:
Step 1: open the shield lock (1);
Step 2: Align the bump (2) on the shield with the notch
on the gearbox;
Step 3: Press down the shield until the shield is
inserted into the gearbox, and the bump (2) is engaged
in the groove on the gearbox (3);
Step 4: Rotate the shield between the output shaft and
the operator. Select an appropriate angle, and then
lock the buckle (1).
Adjustment of shield: (Figure E)
When the shield is delivered, it has been pre-adjusted
to a position where it can be tightened. If the shield
becomes loose after a period of use, tighten the screw
(1) in the figure with the shield tightened. Removal of
shield:
In reverse order of installation: first loosen the buckle,
rotate the shield, and align the bump on the shield
with the notch on the gearbox and pull out the shield
vertically.
Installation and removal of wheel (see Figure F.G.H)
WARNING
When the tool is equipped with a wheel, be sure to use
the wheel shield. The wheel may be crushed during
use. The shield may help reduce the risk of personal
injury.
Installation of wheel:
Step 1: Turn off the switch and pull out the battery
pack
J
K
1
2
L
M
N
inner pressure plate
external pressure plate
The thickness of disk is greater than 3MM
inner pressure plate
external pressure plate
The thickness of disk is less than 3MM
I
Summary of Contents for 51090C
