TOP CAT 36G-2 General Operators Instructions And Maintenance Manual Download

Page: 1 / 12

General Operators Instructions

and

Maintenance Manual

36G Series

Die Grinders

Top Cat ® Air Tools, Manufactured by T.C. Service Co.

38285 Pelton Road, Willoughby, OH 44094 U.S.A.

Ph: (440) 954-7500 or (800) 321-6876 ● Fax: (440) 954-7118 or (877) 800-3589

E-Mail: [email protected] ● Web Site: www.tcservice.com

Read Safety Recommendations Before Operating Tool

Model

Number

Exhaust

Direction

Throttle

Type

Rated

Speed

Power

Output

Case

Material

Weight

Overall

Length

Diameter

Working Air

Consumption

Collet

Size

Aluminum

Steel

36G-2

(F) Front

Side

(L) Lever

(K) Safety

Lever

30000

R.P.M.

0.6 H.P.

(450 W)

Steel

Aluminum

0.8 lb.

(0.4 Kg.)

1.0 lb.

(0.5 Kg).

5.2 Inches

(133 mm)

1.3 Inches

(33 mm)

20 cfm

(9.4 L/S)

1/4”

36G-4

5.3 Inches

(135 mm)

1/8”, 3/16”,

1/4”, 3 mm,

or 6 mm

*The use of type 1 or 27 wheels is not within the design of this pneumatic tool.

36GL

36G Series Die Grinders

Capacity*

● Burrs and Mounted Stones

Summary of Contents for 36G-2













Search results

Summary of Contents for 36G-2

Reviews:

Related manuals for 36G-2

Brands by name

Popular brands

TOP CAT 36G-2, General Operators Instructions And Maintenance Manual

Search results

Summary of Contents for 36G-2

Reviews:

Related manuals for 36G-2

Brands by name

Popular brands