17
V_SC_51075C_202104
speed. The change range is from 0 to maximum
speed. When the force applied is low and the
speed is low, the starting speed will be low,
making the tool stable and easy to control. After
a stable and reliable start, fully press down the
switch for a higher speed.
3. Speed position selection (see Figure C)
During use, select the gear and control the
speed with the switch. Upon delivery, the
machine tool is set at the highest gear. The gear
indicator (6) is provided by three red indicators.
If 3 red indicators are on, this indicates a high
gear; if 2 red indicators are on, this indicates
a medium gear; and if 1 red indicator is on,
this indicates a low gear. If the gear selection
must be changed, press the icon to change
through the gears one by one.
WARNING
Do not press the switch for a long time when
operating at low speed as this will cause the
internal part of the machine tool to become
overheated. Change the speed gear of the
machine tool after each stop.
4. Switch locking (see Figure D)
The switch has a locking protection function will
is beneficial for helping to reduce the possibility
of misstarting the machine tool after a period
of disuse. Adjust the reversing yoke (2) to the
central position when the machine is not used
so as to lock the machine tool.
5. Rotation reversing (see Figure D)
Forward rotation: Push the side of the reversing
yoke (2) marked “
" to the bottom (move to
the left side) and it can be used for tightening
bolts or nuts. Reverse rotation: Push the side
of the reversing yoke (2) marked "
" to the
bottom (move to the right side) and it can be
used for loosening bolts or nuts.
WARNING
The rotation direction can only be changed after
the machine tool has completely stopped.
6. Installation and removal of socket (see
Figure E)
Attention: When installing or removing the
socket, ensure that the machine tool is powered
off and the battery pack is removed.
1) Socket without O-ring and pin
Install the socket: Press it onto the square drive
bit (1) of the tool until it is fully in position.
Remove the socket: For removal, it is only
necessary to pull it out. Tap it gently if necessary.
WARNING
Before starting the machine tool, ensure that
the socket has been installed properly.
7. Work light
The machine tool is equipped with a work light.
When the switch is pressed during operation, the
light will turn on; when the switch is released,
the light will turn off after a delay of 15 seconds.
8. Battery level indication
When you press the machine tool switch, the
battery level indicator will turn on for 5 seconds.
The remaining power level of the battery pack
can be judged according to the following table:
0-25%
25-50%
50-75%
75-100%
LED display
Remaining battery
Summary of Contents for 51075C
