![background image](http://html1.mh-extra.com/html/sata/51005/51005_user-manual_1200204015.webp)
中文
EN
DE RU KO PT
JA
ES
51005
15
4. Speed change
(
see Figure C
)
:
1
)
Move the shift yoke
(
3
)
downwards to the Lo speed:
high torque / low rotating speed for drilling a thicker bit or driving the screw.
2
)
Move the shift yoke
(
3
)
upwards to the Hi speed:
low torque / high rotating speed for drilling a thinner bit.
When the mechanical shift lever cannot be toggled due to teeth collision, tap the switch to rotate the motor and then change the
position.
Warning:
The rotating speed can only be changed after the machine is completely still.
5. Installation or removal of bit
(
see Figure D
)
:
Caution: When installing or removing the bit, be sure to confirm that the drill has been turned off and that the battery pack has been
removed.Hold the machine in one hand, hold the chuck collar in the other hand, turn the chuck counterclockwise to open it, load the bit
into the chuck, push it as far as possible, and then tighten the chuck by rotating the collar clockwise. Hold the collar and rotate it
counterclockwise to remove the bit.
6. Torque and drill setting
(
see Figure E
)
:
Rotate the torque adjusting ring to adjust the torque of machine. When the number 1 on the torque adjusting ring is aligned with the
indicating arrow on the machine, the torque will be minimal. When the mark on the torque adjusting ring is aligned with the indicating
arrow above the machine, the torque will be maximum.
Setting reference is as follows:
1-4
Rotate the small screw
5-8
Drive the screw into the soft material
9-12
Drive the screw into the soft or hard material
13-16
Drive the screw into the hard material
17
Drive the larger screw
High-strength drilling
7. Work light:
Machine is equipped with the work light: when the switch is pressed, the light will come on; when it is released, light will go out.
8. Spindle self-locking:
The spindle self-locking function allows the machine to operate as a hand tool. When the battery pack is exhausted, you can manually
rotate the machine to tighten or loosen the screw. In this case, the chuck is stationary.
9. Drilling operation:
When drilling on the surface of hard material, first mark the area where you want to drill with the pointed punch and hammer to prevent
the bit from slipping. Hold the hand drill, align the bit tip with the mark, and press the switch to drill. Drill with the appropriate pressure.
Do not apply excessive pressure or deviated pressure to increase the diameter.
Note:
The intact high-speed steel bit shall be used for the drilling on metal. For the short screwdriver bit, use a magnetic connecting
rod
(
not included
)
. When tightening the screw, apply a little soap or other lubricant to the thread to facilitate the operation.
Summary of Contents for 51005
