background image

 

 

 
 
5.2.

 

 ALTERNATIVE FUEL 

 
The alternative fuel for coal heating boilers of  SAS  NWT type is a mixture of the black coal 
grades as follows:  70% of coal the nut grade (  class 24/12  acc. to  above mentioned norm)  
and  30%   of  coal  the fine  coal  grade (class  21/15  acc. to above mentioned norm). These 
boilers are also fit fir combusting long flame fuels, such as: brown coal and wood in different 
forms, e.g. chips, silver, shavings, etc. 
 
The  wood  has  to  be  seasoned  at  least  one  year!    Wet  wood  combustion  lowers  the 
efficiency  and  the  lifetime  of  a  boiler.    It  also  obstructs  the  declared  power  for  slow 
combustion  sustainment.  For  this  type  of  boiler  it  is  not  recommended  to  relay  only  on  the 
fine coal. 
 
 
 
 

 

 

Boiler’s    assembling  should  be    performed        by  qualified    and  authorized    personnel    
(qualified  person    upon  adequate  training  and  authorized  for  performing  maintenance  and 
repair works).  
The    fitter’s    obligation    is    to    get    familiar    with    the    product,        its    functioning    and  
protection  systems functionality. 

 

Prior  to    boiler’s  assembling    it    is  strictly  necessary    to  get  familiarized    with  the 
content  of  hereby 

Technical-Start-Up Documentation. 

 
6.1.

 

REQUIREMENTS FOR BOILER-ROOM 

 
The boiler room,  where  the  heating  boiler  for central heating  installation  shall  be  
installed,  must  conform 

the  requirements  of  detailed  regulations  being  in  force,  at  the  

country  of  destination  (e.g.  PN-87/B-02411).  
In particular, the following requirements shall be fulfilled: 

 

the  boiler  rooms  should  be  located  as  centrally  as  possible  to  rooms  which  are  

covered    with    heating  system,    and  the  boiler  itself  should  be  placed  as  close  as 
possible to  chimney  (chimneys), 

 

boiler room entrance door should be opened on the outside, and  be made of 

inflammable materials, 

 

the  boiler  room  should  have  air  blow-in  ventilation,  a  channel    with  section  no  

less  than  50%    of  the   chimney  section,   but not  less than   21 x 21   cm,   with 
the exit at the back part  boiler’s room ,  (lack of such ventilation or obstruction may 
cause:  smoking,  inability to get higher temperature), 

 

the boiler room  should  have  air blow-out  ventilation under room’s  ceiling with  

section  no less  than  25%  of  the  chimney  section,  but  not  less  than    14 x 14  cm    
(the  purpose  of  this  system  is to carry out harmful gases). 

 
NOTE:   Employing of  mechanical blow-out ventilation is  unacceptable. 
 
The boiler room should be provided with day and artificial lighting. 

6. BOILER’S ASSEMBLY GUIDELINES

 

Summary of Contents for NWT























Reviews: