Sapido PCI022 MZK-KR150NUS User Manual Download Page 75

Page: 75 / 106

http://www.sapido.com.tw 74 USER MANUAL V1.0

1. Update

Firmware

Click on

Browse…

button to search your local hard drive and locate the firmware to be

used for update.

Upload & Reset:

Click

Upload

to upgrade the firmware or

Reset

to restore to factory default Settings

Note: 1. To prevent the firmware upgrading interrupted by other wireless signals and caused failure. We

recommend using wired connection to do the upgrading.

The upgrade firmware will not remove your previous settings.

Reset button:

On the back of this router, there is a reset button. If you can not login the administrator page

by forgetting your password; or the router has problem you can’t solve.

You can push the

reset button for 10 seconds with a stick. The router will reboot and all settings will be restored

to factory default settings. If the problem still exists, you can visit our web site to see if there is

any firmware for download to solve the problem.

Summary of Contents for PCI022 MZK-KR150NUS











































































































Search results

Summary of Contents for PCI022 MZK-KR150NUS

Reviews:

Brands by name

Popular brands

Sapido PCI022 MZK-KR150NUS, User Manual

Search results

Summary of Contents for PCI022 MZK-KR150NUS

Reviews:

Brands by name

Popular brands