manualshive.com logo in svg

Sapido PCI022 MZK-KR150NUS, User Manual

Share
Download
Sapido PCI022 MZK-KR150NUS User Manual Download Page 49

 

http://www.sapido.com.tw                              48                                            USER MANUAL V1.0

4.3.2 Wireless 

Advanced 

Settings 

Please follow the instructions to configure the 

Wireless

 settings.

 

 

 

1. Fragment 

Threshold 

To identify the maximum length of packet, the overflow packet length wil be fragmentized. 

The allowed range is 256-2364, and default length is 2346 bytes.   

2. RTS 

Threshold 

This value should remain at its default setting of 2347. The range is 0~2347. Should you 

encounter inconsistent data flow, only minor modifications are recommended. If a network 

packet is smaller than the present RTS threshold size, the RTS/CTS mechanism will not be 

enabled. The router sends Request to Send (RTS) frames to a particular receiving station 

and negotiates the sending of a data frame. After receiving an RTS, the wireless station 

responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. 

Fill the range from 0 to 2347 into this blank.   

3. Beacon 

Interval 

Summary of Contents for PCI022 MZK-KR150NUS











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands