manualshive.com logo in svg

Sanwa MT-5, User Manual

Share
Download
Sanwa MT-5 User Manual Download Page 70

59

How to Use Each Feature

How to Use Each Feature

● 

Due to wearing and tearing of the internal mechanical elements over 

the usage time, the neutral position and the operation angle might 

become off. In such case, you can correct the neutral positions of 

the steering and the throttle and the operation angle.

1) Select [SYSTEM] with the multi-selector and determine with the 

Enter operation.

2) Select [CALIBRATION] with the multi-selector and determine with 

the Enter operation.

3) Select a channel to calibrate with the multi-selector and determine 

with the Enter operation.

4) When selecting [STEERING], operate the Enter with the steering 

wheel in neutral, then operate the steering wheel fully to left and 

right.

5) When entering the range, [OK] is displayed. Operate following the 

display.

6) When calibration is done, [Executed] is displayed. 
7) If the throttle side also needs calibration, refer to the steering to set.
  *Unless necessary, do not set up calibration. If the setting is not 

done properly, it may not operate normally.

● 

About Steering wheel angle adjustment

  MT-5 can adjust steering wheel angle. Please take off wide steering 

pad and put hex screws in accesory box on holes of steerig wheel 

(there are 2 holes at steering wheel). Please adjust steering angle 

by the hex screws. (*Both screws height must be equally).

  *After adjusting steering wheel angle, Calibration is required. 

Hex wrench

(1.5 mm)

ENTER

BACK

ENTER

BACK

⇒

ENTER

Select Yes, if it is OK.

Yes Selected.

Calibration complete

Wheel Adaptor

SUPPLEMENT

●If not correctly working after calibration, please calibrate again
  or setting changes USER to FACTORY. If the operation does

  not return to normal after calibration,  contact Sanwa Service.

●In case steering wheel angle was too narrow, calibration will
   not be able to work correctly. Please do NOT extremely tight
   hex screws for steering wheel angle adjustment. 
●When changing back angle to default, please loose hex screws
  until do not touch the steering base.  After loosing the 
  hex screws, please do calibration again. 
●Please do CALIBRATION when changing steering,
  throttle tension, or some parts for steering or throttle. 

SYSTEM MENU

SYSTEM

CALIBRATION

Summary of Contents for MT-5















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands