background image

 

 

A4b Automatic Dispenser                                                       

  V1.0                                                                                           

3.1 

USB/COM Interface 

Windows 2000 or higher operating system 

2. Specifications 

Type

A4b      Mode

aaa 

Item 

Content 

Item 

Content 

Number of Canisters 

24/20/18/16/12 

Min Dispensing 

0.077ml

1Y/384

 

Flow Rate/Frequency 

400ml/min 200ml/min 

Canister Size 

2.3/3.8 Ltr 

Pump Size 

62mltr 

Stirring Speed 

20 Cycles/minute 

Diameter of the punch’s head  25mm 

Max Base Paint Can Weight 

40KG 

Power 

≤200W 

Power Supply 

See Nameplate 

Can Size(D x H) 

MAX320mm×390mm 

MIN80mm×110mm 

Stirring Timing 

Stir 10 minutes 

every 4 hours 

Noise Level 

<70dBA 

Weight

 

270±3 kg 

Machine Size (Height x Width x Depth) 

1335×900×1000

mm

 

Notes: Timed stirring function is available for customization.   

3. Safety Instructions 

1). Please read this manual carefully before installation and operation. 

2). All the operation and maintenance must be carried out by authorized personnel. 

3). Prolonging wire is prohibited. 

4). The machine is only available for 0.5 liter to 20 liter (40kg) paint cans. 

5). The machine should be powered on all the time to make the stirring available.   

6). Press the emergency stop button, the machine will stop working and the stirring will stop at the same 

time. 

7). If it is not used for a long time, the canisters should be cleaned and plugged off. 

8). During first use, please discharge the fixing seats of the machine( as fig. 3.1, left one and right one) 

and keep the fixing seats for next transportation. 

 

 

 

 

Fixing Seat 

色浆桶部件

 

Summary of Contents for A4B Series




















Reviews: