background image

4

   

S&C Instruction Sheet 665-506

Safety Information

Understanding 
Safety-Alert Messages

There  are  several  types  of  safety-alert  messages  which  may  appear  throughout  this 
instruction sheet as well as on labels attached to the S&C Manual PME Pad-Mounted 
Gear . Familiarize yourself with these types of messages and the importance of the various 
signal words, as explained below .

Ç

 DANGER

“DANGER”  identifies  the  most  serious  and  immediate  hazards  which 

will  likely

 

result in serious personal injury or death if instructions, including recommended 
precautions, are not followed .

Ç

 WARNING

“WARNING”  identifies  hazards  or  unsafe  practices  which 

can

  result  in  serious 

personal injury or death if instructions, including recommended precautions, are 
not followed .

Ç

 CAUTION

“CAUTION” identifies hazards or unsafe practices which 

can

 result in minor personal 

injury  or  product  or  property  damage  if  instructions,  including  recommended 
precautions, are not followed .

NOTICE

“NOTICE” identifies important procedures or requirements that 

can

 result in product 

or property damage if instructions are not followed .

Following 
Safety Instructions

If you do not understand any portion of this instruction sheet and need assistance, contact 
your nearest S&C Sales Office or S&C Autho rized Distributor, or call S&C Headquarters 
at (773) 338-1000, Monday through Friday between 8:30 AM and 5:00 PM Central Standard 
Time . (In Canada, call S&C Electric Canada Ltd . at (416) 249-9171, Monday through Friday 
between 8:00 AM and 5:00 PM Eastern Standard Time .)

Ç

 DANGER

Read this instruction sheet thoroughly and carefully 
before installing or operating your S&C Manual PME 
Pad-Mounted Gear .

Replacement  
Instructions  
and Labels

If you need additional copies of this instruction sheet, contact your nearest S&C Sales 
Office, S&C Authorized Distributor, S&C Headquarters, or S&C Electric Canada Ltd .

It is important that any missing, damaged, or faded labels on the equipment be 

replaced immediately . Replacement labels are available by contacting your nearest 
S&C Sales Office, S&C Authorized Distributor, S&C Headquarters, or S&C Electric 
Canada Ltd .

Summary of Contents for PME Pad-Mounted Gear

















Reviews: