Samsung WA85N6750B Series User Manual Download Page 36 | Manualshive

Page: 36 / 48

background image

36 English

Maint

enanc

e

Maintenance

Pump filter (applicable models only)

1.

Put a floor-cloth or towel under
the Pump filter. Turn the filter knob
anticlockwise to remove.

2.

Clean the filter with running water and a
soft brush.

3.

Reinsert the filter, and turn clockwise
until it locks into position.

WA6700N_DC68-03892N-01_EN.indd 36

2018-05-24 11:46:33

«
...
34
35
36
37
38
...
»

Summary of Contents for WA85N6750B Series

















































Reviews:

No comments

Related manuals for WA85N6750B Series

Brand: Kärcher Pages: 196

Brand: Kärcher Pages: 65

Brand: Kärcher Pages: 20

Brand: Kärcher Pages: 208

HD 4.5/32-4 S Eb HD 4.5/32-4 S Ec

Brand: Kärcher Pages: 36

Brand: Kärcher Pages: 44

Brand: Kärcher Pages: 264

Brand: ECG Pages: 116

Brand: Kärcher Pages: 16

DISHDRAWER DD60DHI9

Brand: Fisher & Paykel Pages: 19

Brand: VESTEL Pages: 16

Brand: Lett Pages: 52

Brand: Daewoo Pages: 50

Super 20 CL8761

Brand: Speed Queen Pages: 41

Brand: Asko Pages: 28

Brand: Ramteq Pages: 12

Brand: Tricity Bendix Pages: 24

Brand: Easy-Kleen Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands