Samsung UDH4400G Service Manual Download Page 10

Page: 10 / 79

2-5 Air Filter Installation

1. Remove the air inlet duct flange.

2. Attach the air filter kit to the air inlet side of

indoor unit.

3. To clean the air filter, remove the fixing bracket

on the base of air filter kit, then pull out the
filter.

Note: Setting Up Filter Cleaning Cycle

• Adjust the DIP switch(SW2) in the main PCB to

the desired position referring the table below.

Samsung Electronics

2-5

Switch No.

Switch Position

OFF

Filter Cleaning Cycle

1,000 hours
2,000 hours

Caution :

•The optional kits must be installed by an installation

specialist.

•Before installing the optional kits, ensure that you have

turned off the main power.

•The optional air filter has to be cleaned only by an

authorized person or service agent.

2-00216A(1)-PR 5/19/01 10:05 AM Page 2-5

Summary of Contents for UDH4400G
















































































Search results

Summary of Contents for UDH4400G

Reviews:

Related manuals for UDH4400G

Brands by name

Popular brands

Samsung UDH4400G, Service Manual

Search results

Summary of Contents for UDH4400G

Reviews:

Related manuals for UDH4400G

Brands by name

Popular brands