Samsung UDH4400G Service Manual Download Page 37

Page: 37 / 79

4-10

Samsung Electronics

■

EC06 : When the trouble is found in the communication related part between indoor unit

and wired remote controller. (during single operation, not group control)

- EC of 7-segment of outdoor unit PCB.
- Wireless receiving board lamp and reservation lamp is flickering with 1Hz.
- Action item when “C” displays on the wired remote controller.

Trouble Shooting

Check point :

- Short circuit or mis-connection of the communication line between indoor unit and wireless remote controller

- Indoor unit PCB defect

- Wired remote controller PCB defect

✽

“0” stands for the indoor unit address.

YES

Connect correctly and check.

Connect correctly and check again

Set address to "0"

Replace the wired remote controller

Are the terminals R1, R2, R3 of indoor unit terminal

board connected correctly to R1, R2, R3 of wired remote

controller?

Is 7P(RED) of transformer connected to CN11

of indoor unit?

Is the jump wire inserted into CN20 of indoor unit PCB?

Is the address of PCB digital switch of indoor unit to "0"?

Replace the indoor unit PCB

3-00216A(1)-TS 5/19/01 10:06 AM Page 4-10

Summary of Contents for UDH4400G
















































































Search results

Summary of Contents for UDH4400G

Reviews:

Samsung UDH4400G, Service Manual, Page: 37 / 79

Search results

Summary of Contents for UDH4400G

Reviews: