Samsung UDH4400G Service Manual Download Page 29

Page: 29 / 79

4-2

Samsung Electronics

If the error occurs, the indicators on the receiver & display unit displays the error.

Meaning of Error Code

Checking area

◆

Indoor unit thermistor sensor

◆

PCB of the indoor unit

Meaning

Indicators

Indoor unit thermistor sensor error

◆

Indoor unit pipe sensor

◆

PCB of the indoor unit

Indoor unit pipe sensor error

◆

Outdoor unit thermistor sensor

◆

PCB of the outdoor unit

Outdoor unit thermistor sensor error

◆

Drain pump, Float switch

◆

Drain system

Float switch error

◆

Communication cables of indoor and

outdoor units

◆

PCB of indoor and outdoor units

Indoor and Outdoor communication
error

◆

Wired remote controller cables,

Wired remote controller

◆

Main/Sub PCB of the indoor unit

Wired remote controller
communication error

◆

Outdoor pipe sensor

◆

PCB of the outdoor unit

Outdoor pipe sensor error

◆

Three phase power connecting

◆

PCB of the outdoor unit

Three phase power incorrect
connecting error
(In case of three phase power models)

: OFF : Blinking : Blinking at once : Blinking alternately

▲

▲ ▲

Timer

Operating

Filter

4-2 Wireless Remote Controller

3-00216A(1)-TS 5/19/01 10:06 AM Page 4-2

Summary of Contents for UDH4400G
















































































Search results

Summary of Contents for UDH4400G

Reviews:

Samsung UDH4400G, Service Manual, Page: 29 / 79

Search results

Summary of Contents for UDH4400G

Reviews: