Samsung UDH4400G Service Manual Download Page 42

Page: 42 / 79

Samsung Electronics

4-15

■

EC11 : When the trouble is found on the part related to the fan motor of outdoor unit.

Trouble Shooting

Check point :

- Outdoor unit PCB relay defect

- Output of outdoor unit micom

- Outdoor unit fan motor defect

- Defect of IC07 of outdoor unit PCB

YES

Check and replace

the related part

YES

Is the power source normal? AC220~240 50Hz

Is the wire harness for motor connection good?

Is the terminal contact of fan motor condenser good?

Does the outdoor fan motor changes to mild

and strong wind during the cooling

operation?

Do the RY73, RY74 operate?

Normal

Check and replace

the micom

Check and replace

the relay

Check and replace

IC07

Replace PCB

Is the wind volume output pin of micom high

when each wind control is operation?

Is the voltage across the PCB relay 12V

when the each wind control of micom

is opeating?

Are the pins 11 and 12 of IC07 of outdoor

unit PCB low when each wind control mode

micom is operation?

Is the voltage across the outdoor unit

fan motor AC220~240V?

Check outdoor unit fan motor and replace

3-00216A(1)-TS 5/19/01 10:06 AM Page 4-15

Summary of Contents for UDH4400G
















































































Search results

Summary of Contents for UDH4400G

Reviews:

Related manuals for UDH4400G

Brands by name

Popular brands

Samsung UDH4400G, Service Manual

Search results

Summary of Contents for UDH4400G

Reviews:

Related manuals for UDH4400G

Brands by name

Popular brands