background image

O p e r a t i o n

Power Control

The power control slide switch on the front of the cleaner turns the vacuum on and off. 
This switch also allows you to control the cleaning power. 

1

Plug cord into electrical outlet. 

2

To turn the vacuum cleaner on, slide the power switch up. To turn it off, slide the
switch down. The headlight turns on when in use. 

Handle Release

Select the desired angle of the cleaner using the handle release pedal. 
The handle of your cleaner has three positions.

1

Step on the handle release pedal on the back of the cleaner base. 

2

Raise or lower the handle and release the pedal.

A.  Upright position:

For storage and elevated cleaning with cleaning tools.

B.  Middle position: 

For general operation on carpet and floors.

C.  Low position: 

Use for reaching under low furniture, step on handle release 
lever to lower handle.

Brush roll switch

Turn brush roll switch off to clean hard surface floors.
Turn brush roll switch on to clean carpet and rugs.
The brush rolls will automatically turn off when the handle is in the
upright position.

OFF

OFF

A

B

C

CIRCUIT BREAKER
(RESET SWITCH)

BRUSH ROLL
SWITCH

6

Summary of Contents for SU8583
















Reviews: