Samsung ST43L2HD Instruction Manual Download Page 14

Page: 14 / 92

Your New Wide TV

Front Panel LED Indicators

The three lights on the front panel indicate the status of your TV.

Indicator Light Key

: Light is On
: Light is Blinking

: Light is Off

• It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.
• The TV has a fan to keep the inside lamp from overheating. You’ll occasionally hear it working.

Timer

Lamp

Temp

Indication

Auto Timer ON/OFF has been set

Standby state.

The picture will automatically appear in about 25 seconds.

Auto Timer ON/OFF has been set and the set will automatically be turned on in

about 25 seconds.

A cooling fan inside the set is not operating normally.

Lamp cover on rear of the set is not properly shut.

Check if the ventilation hole on the rear of the set is blocked, because if the

inner temperature is too high, the power will shut off.

Lamp may be defective. Please contact a certified technician.

Summary of Contents for ST43L2HD





























































































Search results

Summary of Contents for ST43L2HD

Reviews:

Related manuals for ST43L2HD

Brands by name

Popular brands

Samsung ST43L2HD, Instruction Manual

Search results

Summary of Contents for ST43L2HD

Reviews:

Related manuals for ST43L2HD

Brands by name

Popular brands