Samsung SRD-440 User Manual Download Page 94

Page: 94 / 120

94_

appendix

PRODUCT SPECIFICATION

Item

Details

Video

Inputs

4 composite video 0.5–1 Vpp, 75 ohm

Resolution

704x480 NTSC, 704x576 PAL

Live

Frame rate

120fps NTSC, 100fps PAL

Resolution

704x480 NTSC, 704x576 PAL

Multi Screen display

1, 4, SEQUENCE, PIP

Performance

Operating System

Embedded

Linux

Recording

Compression

H.264

Record Rate

NTSC : Up to 30fps @ 704x480 / PAL : Up to 25fps @ 704x576

NTSC : Up to 60fps @ 704x240 / PAL : Up to 50fps @ 704x288

NTSC : Up to 120fps @ 352x240 / PAL : Up to 100fps @ 352x288

Mode

NTSC : Manual, Schedule (Continuous/Event), Event (Pre/Post)

PAL : Manual, Schedule (Continuous/Event), Event (Pre/Post)

Overwrite modes

Continuous

Pre-Alarm

Up to 5sec.

Post-Alarm

Up to 6 hour. (5, 10, 20, 30 sec, 1, 3, 5, 10, 20 min,1, 2, 3, 4, 5, 6 hour)

Search & Playback

Search mode

Date/time, Event, Back up, POS, Motion

Playback function

Fast Forward/Backward, Slow Forward/Backward, Step Forward/Backward

Network

Transmission speed

100 / 120fps

Bandwidth

Up to (4)Mbps, Unlimited(4M)/2/1.5/1 Mbps/800/600/500/400/300/200/
100/50 kbps

Bandwidth control

Automatic

Stream

H.264(CIF)

Maximum No. of remote
users

Search(2) / Live Unicast(4) / Live Multicast(20)

Protocol support

TCP/IP, DHCP, PPPoE, SMTP, NTP, HTTP, DDNS, RTP, RTSP

Monitoring

Webviewer, CMS(Smart viewer, NET-i)

Smartphone

Support

Protocol support

RTP, RTSP, HTTP, CGI

Transmission speed

CIF Max 15fps(Single Channel) / CIF Max 2fps(Quad Channel)

Remote users Maximum

Live(1)

Summary of Contents for SRD-440

























































































































Search results

Summary of Contents for SRD-440

Reviews:

Related manuals for SRD-440

Brands by name

Popular brands

Samsung SRD-440, User Manual

Search results

Summary of Contents for SRD-440

Reviews:

Related manuals for SRD-440

Brands by name

Popular brands