Samsung SRD-440 User Manual Download Page 68

Page: 68 / 120

68_

web viewer

CONNECTING WEB VIEWER

Open your web browser and type the IP address or URL
of DVR into the URL address box.

The basic URL of the DVR is as following in case of MAC
address :



http://www.samsungipolis.com/Product domain (registered at
the iPOLiS web site)



You can also use registered URL which setups up in the Setup menu of your DVR.

Set the Admin ID and password same to those of the DVR
Admin.
For general users, enter the DVR user ID and password.



The default password can be exposed to a hacking thread so
it is recommended to change the password after installing the
product.
Note that the security and other related issues caused by the unchanged password shall be responsible for the user.



It allows up to 4 simultaneous access including the Admin and general users.



It does not allow multiple login of the Admin user.



Initial password of the Admin user is set to “4321”.



Password of the Admin and general users can be changed in <

Permission Management

> menu of the DVR.



Normal users should have set <

Viewer

> under <

Permission Management

> to “Use” before connecting to the

Web Viewer. (Page 33)



All settings are applied by the DVR’s settings.

Click <

Install ActiveX Control…

Downloading Active-X control may take several minutes
according to the security settings on your PC.

Click <

Install

Summary of Contents for SRD-440

























































































































Search results

Summary of Contents for SRD-440

Reviews:

Related manuals for SRD-440

Brands by name

Popular brands

Samsung SRD-440, User Manual

Search results

Summary of Contents for SRD-440

Reviews:

Related manuals for SRD-440

Brands by name

Popular brands