![background image](http://html.mh-extra.com/html/samsung/sgh-e820/sgh-e820_service-manual_1190644008.webp)
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Circuit Description
2-4
For the purpose of enabling YMU765_MA5 to demonstarte its full capablities, Yamaha purpose to use "SMAF:Synthetic
music Mobile Application Format" as a data distribution format that is compatible wiht multimedia. Since the SMAF takes
a structure that sets importance on the synchronization between sound and images, various contents can be written into it
including incoming call melody with words that can be used for traning karaoke, and commercial channel that combines
texts, images and sounds, and others. The hardware sequencer of YMU765_MA5 directly interprets and plays blocks
relevant to systhesis (playing music and reproducing ADPCM with FM synthesizer) that are included in data distributed in
SMAF.
9. Memory
Signals in the OM6359 enable two memories. They use only one volt supply voltage, VDD3 in the PCF50601. This
system uses Samsung's memory, KBB06B400M-F402. It is consisted of 128M bits flash NOR memory and 256M bits
flash NAND memory and 64M bits SCRAM. It has 16 bit data line, HD[0~15] which is connected to OM6359 and
MV317SAQ. It has 26 bit address lines, HA[1~26]. CS_NAND and NCSRAM signals is chip select.
Writing process,
HWR_N is low and it enables writing process to flash memory and SRAM. During reading process, HRD_N is low and
it enables reading process to flash memory and SRAM. Each chip select signals in the OM6359 select memory among 2
flash memory and SCRAM. Reading or writing procedure is processed after HWR_N or HRD_N is enabled. Memories
use reset, which is VDD3 delay from PCF50601. HA[25] signal enables lower byte of SRAM and HA[26] signal enables
higher byte of SRAM.
10. OM6359
OM6359 is consisted of ARM core and DSP core. It has 8x1Kword on-chip program/data RAM, 55 Kwords on-chip
program ROM in the DSP. It has 4K*32bits ROM and 2K*32bits RAM in the ARM core. DSP is consisted of KBS,
JTAG, EMI and UART. ARM core is consisted of EMI, PIC(Programmable Interrupt Controller), reset/power/clock unit,
DMA controller, TIC(Test Interface Controller), peripheral bridge, PPI, SSI(Synchronous Serial Interface),
ACC(Asynchronous communications controllers), timer, ADC, RTC(Real-Time Clock) and keyboard interface.
KBIO(0:7), address lines of DSP core and HD[0~15]. HA[1~26], address lines of ARM core and HD[0~15], data lines of
ARM core are connected to memory, YMU765, MV317SAQ(Camera DSP Chip).
CS_NAND, NCSRAM, NCSFLASH in the ARM core are connected to each memory. HWR_N and HRD_N control the
process of memory. External IRQ(Interrupt ReQuest) signals from each units, such as PMU, need the compatible process.
KBIO[0~7] receive the status from key and RXD0/TXD0/irDA_DOWN are used for the communications using IRDA and
data link cable(DEBUG_DTR/RTS/TXD/RXD/CTS/DSR).
It has JTAG control pins(TDI/TDO/TCK) for ARM core and DSP core. It recieves 13MHz clock in CKI pin from external
TCXO. ADC(Analog to Digital Convertor) part receives the status of temperature, battery type and battery voltage.
11. VC-TCXO-214C6(26MHz)
This system uses the 26MHz TCXO. AFC control signal forms OM6359 control frequency from 26MHz x-tal. It generates
the clock frequency. This clock is connected to UAA3536.