English-6
Safety information
2
-4
CAUTION
Before use
• Insert the dustbin before using POWERbot.
• Open room doors before cleaning in order
to have all rooms cleaned and install
a Virtual guard in front of entryway,
balconies, bathrooms, or other areas
where POWERbot may fall.
• Be careful with the followings for proper
automatic recharging.
– Always turn on the power of the
docking station.
– Install the docking station where
POWERbot can easily find.
– Do not leave any object in front of the
docking station.
• When installing the docking station, do
not leave the cord carelessly on the floor
since POWERbot may get tangled by it.
• Do not use POWERbot on black colored
floors.
– The POWERbot may not be able to
operate normally.
• Do not pick up POWERbot by the dustbin
holder.
• Do not place any objects within 0.5 m
to both sides and 1 m to the front of the
docking station.
• Make sure the docking station's charging
contact is not damaged or have any
foreign matters on it.
• Do not install the docking station in an
area with a dark floor.
– If the floor around the docking station is
dark, recharging is hindered.
• Move any obstacles that may disturb
POWERbot's movement (such as children's
indoor swing or slides) before cleaning.
In use
• Using POWERbot on thick carpet may
damage both POWERbot and the carpet.
– The POWERbot cannot pass over carpet
that is thicker than 1 cm.
• Do not use POWERbot on tables or other
high surfaces.
– There is a risk of damage if it falls.
• The POWERbot may bump into chair, desk
legs therefore move them away for faster
and efficient cleaning.
• When POWERbot is operating, do not lift
it up or carry it to another area.
• Do not hold by driving wheels of
POWERbot when carrying it to another
area.
• Do not put any objects on top of
POWERbot since it may cause malfunction.
• Remove any large papers or plastic bags
immediately when using POWERbot since
they may block the intake.
• Do not aim the red pointer directly at
people or animals.
Cleaning and maintenance
• Prevent any damage to POWERbot by
complying the followings.
– Do not clean POWERbot by spraying
water directly onto it or use benzene,
thinner, acetone or alcohol to clean it.
• Do not disassemble or repair POWERbot.
This should only be done by a certified
repairman.
• Always keep the obstacle sensor and cliff
sensor clean.
– If foreign matter accumulates, sensors
may malfunction.
1_VR9300K_Q_guide_EN_00743M-06_ST.indd 6
2020-01-14 오후 10:24:17
Summary of Contents for POWERbot SR20K9350W Series
