Samsung OfficeServ 7030 General Description Manual Download Page 12 | Manualshive

Page: 12 / 100

background image

2.1

PART 2. HARDWARE DESCRIPTIONS

2.1 SYSTEM CABINET

This paragraph describes the configuration and the functions of the OfficeServ 7030 base unit. The Base unit is a
main control board that controls all functions of OfficeServ 7030. It performs the voice switching function, signal
processing function and Programmable Store System (PSS) management function. Base board carries out the sys-
tem booting function

The OfficeServ 7030 base cabinet
is a complete 4 lines by 8 exten-
sion phone system. It has the
main processor, automated atten-
dant and main memory contain-
ing system software and storage
embedded into the main board
along with other common
resources such as 2 built-in single
line ports, MGI channels, MPS
channels, DTMF sender/receivers,
page relays etc. The 7030 base
cabinet has 4 slots to mount
boards, and AC to DC power sup-
ply, a battery backup connector
and power on/off switch. The
cabinet is designed to be wall
mounted, or placed on a table
top. Slot 1 is exclusively used for
2 single line ports, Slot 2 and 3 are
universal and can be used for
Single line, digital stations, or LAN interface cards. Slot 4 is dedicated the 4TM (analog Trunk) card. One slot is ded-
icated for the modem card.

The base cabinet has openings for mounting the cards into the cabinet. When the cards are mounted the RJ45
connectors provides an interface to 4 CO lines, 8 extensions (digital or LAN), 2 single line ports, a MISC and a LAN
ports. See Figure 2-2.

FIGURE 2-1

FIGURE 2-2

[NOT

USED]

[Not Used]

TOP VIEW

FRONT VIEW

«
...
10
11
12
13
14
...
»

Summary of Contents for OfficeServ 7030





































































































Reviews:

No comments

Related manuals for OfficeServ 7030

DECT Elite 9035+1

Brand: Uniden Pages: 68

Brand: TRIGA Pages: 33

Brand: Main Resource Pages: 5

Brand: VanAccess Pages: 24

Brand: GE Pages: 100

Brand: Vertical Networks Pages: 37

Brand: Aastra Pages: 17

Brand: Blaupunkt Pages: 17

Brand: Exibel Pages: 10

Brand: Gigaset Pages: 8

Brand: LG Pages: 84

Brand: LG Pages: 72

Brand: LG Pages: 30

Brand: LG Pages: 33

Brand: LG Pages: 20

Brand: LG Pages: 26

Brand: LG Pages: 33

Brand: LG Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands