Samsung MT3204 Series Page 11 Installation Manual Download

Page: 11 / 122

Confidential

Preface

MT3204 Series Installation Manual v1.0

Personal and Product Safety

This product safety information includes European directives, which you must
follow. If these do not apply in your country, please follow similar directives that
do apply in your country.

Electrical

The product is designed to operate from a -48 V DC supply and is therefore

classified as Safe Extra Low Voltage (SELV) equipment.
All structural parts are grounded and all input and outputs have built-in isolation

from the network. All input and output ports that connect to external power

sources are designed to meet relevant national safety requirements.
The product contains hazardous energy levels as defined by EN 60950. Care must

be taken when maintaining this equipment as injury to personnel or damage to the

equipment could result from mistakes. Maintenance should only be carried out by

trained and competent engineers who are familiar with the relevant procedures and

instructions.

Lasers

The product is fitted with optic modules rated as Class 1 radiation-emitting devices

under EN 60825-1. During installation, operation, and maintenance, never look

into the end of an optical fiber directly or by reflection either with the naked eye or

through an optical instrument. Do not operate equipment with exposed fiber

connectors-cover these with fiber cables or blanking caps. Do not remove

equipment covers during operation unless requested to do so in the documentation.

Carry out normal safety precautions when trimming fibers during installation.

Manual Handling

Care should be taken when handling equipment. Give due consideration to the

weight of the equipment, the physical capability of the individual(s) handling the

equipment, and movements such as twisting, bending and stooping, which could

lead to skeletal and muscular injuries.

Installation

Installation must be carried out by trained and competent engineers only. All

relevant safety measures should be taken to ensure equipment is not connected to

live power and transmission sources during installation. Equipment must be

correctly installed in order to meet the relevant safety standards and approval

conditions.
Each power feed to the unit requires a separate fused feed from the provided

power supply. The cable between the power distribution point and the installed

equipment must have a minimum cross-sectional area of 2.5 mm

Summary of Contents for MT3204 Series























































































































Search results

Summary of Contents for MT3204 Series

Reviews:

Related manuals for MT3204 Series

Brands by name

Popular brands

Samsung MT3204 Series, Installation Manual

Search results

Summary of Contents for MT3204 Series

Reviews:

Related manuals for MT3204 Series

Brands by name

Popular brands