Samsung MT3204 Series Page 14 Installation Manual Download

Page: 14 / 122

Confidential

Preface

MT3204 Series Installation Manual v1.0

xiv

Battery Disposal

The product contains a battery on the processor card. The battery should not be

disposed of with other household waste. Where marked, the chemical symbols Hg,

Cd or Pb indicate that the battery contains mercury, cadmium or lead above the

reference levels in EC Directive 2006/66. The battery incorporated in this product

is not user replaceable. For information on its replacement, please contact your

service provider. Do not attempt to remove the battery or dispose it in a fire. Do

not disassemble, crush, or puncture the battery.
End of life recycling materials information is available from Samsung.

California USA Only

This Perchlorate warning applies only to primary CR (Manganese Dioxide)

Lithium coin cells in the product sold or distributed ONLY in California USA
‘Perchlorate Material-special handling may apply, See

www.dtsc.ca.gov/hazardouswaste/perchlorate.’

Compliance Statements for the USA

Any changes or modifications that art not expressly approved by the manufacturer

for compliance could void the user's authority to operate the equipment.

Summary of Contents for MT3204 Series























































































































Search results

Summary of Contents for MT3204 Series

Reviews:

Related manuals for MT3204 Series

Brands by name

Popular brands

Samsung MT3204 Series, Installation Manual

Search results

Summary of Contents for MT3204 Series

Reviews:

Related manuals for MT3204 Series

Brands by name

Popular brands