background image

62

GB

MISCELLANEOUS

63

Troubleshooting 

(Con’t)

    

Symptom

Check/Remedy

Disc is rotating but no 
picture is produced.
Picture quality is poor and 
picture is shaking.

Is the TV power on?
Are the video cables connected properly?
Is the disc dirty or damaged?
A poorly manufactured disc may not be playable.




Audio language and subtitles do not 
work.

Audio language and subtitles will not work for DVDs not containing 

them. And depending on the disc, they may work differently.

Menu screen does not appear even when 
the menu function is selected.

Are you using a disc that does not contain menus?

Aspect ratio cannot be changed.

You can play 16:9 DVDs in 16:9 WIDE mode, 4:3 LETTER BOX 
mode, or 4:3 PAN SCAN mode, but 4:3 DVDs can be seen in 4:3 ratio 
only. Refer to the DVD disc jacket and then select the appropriate 
function.

The main unit is not working. 
(Example: The power goes out or 
strange noise is heard.)
The DVD player is not working 
normally.

Turn off the power and hold the 

STOP(

)

 button on the main unit for 

longer than 5 seconds.

Using the RESET function will erase all stored settings. 

Do not use this unless necessary.

The password for rating level has been 
forgotten.

While <NO DISC> message appears on the display of main unit, hold 
the main unit's 

STOP(

)

 

button for longer than 5 seconds. <INITIAL> 

appears on the display and all settings will return to the default values.
Press the POWER button.

Using the RESET function will erase all stored settings. 
Do not use this unless necessary.

Can't receive radio broadcast.

Is the antenna connected properly?
If the antenna's input signal is weak, install an external FM antenna in 
an area with good reception.


Cautions on Handling and Storing Discs    

Small scratches on the disc may reduce sound and picture quality or cause skipping.
Be especially careful not to scratch discs when handling them.

Handling discs 

Do not touch the playback side of the disc. 
Hold the disc by the edges so that 

fi

 ngerprints will not get 

on the surface.
Do not stick paper or tape on the disc.

Disc Storage 

Do not keep in 
direct sunlight

Keep in a cool 
ventilated area

Keep in a clean 
Protection jacket.
Store vertically.

Do not allow the discs to become contaminated with dirt.

Do not load cracked or scratched discs.

Handling and Storing Discs 

When you get 

fi

 ngerprints or dirt on the disc, clean it with a mild 

detergent diluted in water and wipe with a soft cloth.

When cleaning, wipe gently from the inside to the outside of the disc.

Condensation may form if warm air comes into contact with cold parts inside 
the player. When condensation forms inside the player, the player may not 
operate correctly. If this occurs, remove the disc and let the player stand for 
1 or 2 hours with the power on.

Summary of Contents for HT-TX22




































Reviews: