Samsung FlexWash WV16M9945K Series User Manual Download Page 68

Page: 68 / 80

Troubleshooting

English

Symptom

Action

Excessive suds.

•  Make sure you use the recommended types of detergent.
•  Use high efficiency (HE) detergent to prevent oversudsing.
•  Reduce the detergent amount for soft water, small loads, or

lightly soiled loads.

• Non-HE detergent is not recommended.

Cannot add additional
detergent.

• Do not fill the detergent or fabric softener compartments

beyond the marked max fill limit.

The washer stops.

•  Plug the power cord into a live electrical outlet.
•  Check the fuse or reset the circuit breaker.
•  Close the door, and then press and hold

START/PAUSE

to start

the washer. For your safety, the washer will not tumble or
spin unless the door is closed.

• Before the washer starts to fill, it will make a series of

clicking noises to check the door lock and does a quick drain.

• There may be a pause or soak period in the cycle. Wait and

the washer may start.

• Make sure the mesh filters of the water supply hoses at the

taps are not clogged. Periodically clean the mesh filters.

• If the washer is not supplied with sufficient power, the

washer temporarily will not drain or spin. As soon as the
washer regains sufficient power, it will operate normally.

FlexWash_DC68-03768L-00_EN.indd 68

2017-09-13 2:26:20

Summary of Contents for FlexWash WV16M9945K Series

















































































Search results

Summary of Contents for FlexWash WV16M9945K Series

Reviews:

Related manuals for FlexWash WV16M9945K Series

Brands by name

Popular brands

Samsung FlexWash WV16M9945K Series, User Manual

Search results

Summary of Contents for FlexWash WV16M9945K Series

Reviews:

Related manuals for FlexWash WV16M9945K Series

Brands by name

Popular brands