DSR9400 FT
A, EM VIA
DSR9400 FT
A, EM VIA
TROUBLESHOOTING
GB-31
GB-30
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB
1. User section
4000 programmable channels,
software download via satellite & PC,
advanced Electronic Program Guide,
multi-language supported for OSD,
DiSEqC 1.2 supported full function
infrared remote control unit,
auto and manual scan facility,
channel organizing (programmable),
SCARTS output,
low power consumption
2. Tuner section
950 ~ 2150 MHz wide band tuner,
supporting DiSEqC 1.2 version,
13 V/18 V switching,
22 KHz continuous tone control
3. Video section
DVB-S compliant,
MPEG-2 video (MP@ML)
2 - 45 Ms/s symbol rate
compatible for both SCPC/MCPC,
supports aspect ratio 4:3 (normal) and
16:9 (wide screen)
Power supply
Type:
SMPS
Input Voltage:
176-264V AC 50/60Hz
Power Consumption:
Max. 25W
Stand by:
11W
VIDEO DECODER
Transport
MPEG-2 ISO/IEC 13818
Transport stream
Transport stream Specification
MPEG-2 MP@ML
Input Rate
Up to 100Mbps
YUV format
4:2:2
Aspect ratio
4:3, 16:9
Resolution
720 x 576, 704 x 576,
544 x 576, 480 x 576,
352 x 576, 352 x 288
Scale
0.5, 2.0 in both horizontal and vertical
directions
4. Audio section
MPEG 1 audio layer I & II
mono, dual, stereo and joint stereo audio
mode,
32, 44.1 and 48 KHz sampling
frequencies,
volume control and mute function through
Remote Control Unit.
Problem
Possible cause
Solution of the problem
No display LED on
Power cord
Power cord plug in correctly
the front panel;
not plugged in correctly
Back switch in correctly
No power supply
No pictures on the screen
Receiver in Standby mode;
Set receiver to "On";
Scart not connected tightly
Check connection and correct;
to video output of television;
incorrect channel or video
Check channel and video output and
output selected on television
correct (TV instruction manual)
No sound
Audio cord connected
Check connection and correct;
incorrectly;
Loudness level = 0;
Increase loudness on television set;
Muting active
Press the MUTE key
Remote Control does not
incorrect operation;
Point remote control
operate directly
towards the Receiver.
Batteries dead or inserted
Replace batteries or insert correctly
incorrectly
Poor picture quality
Signal strength too low
Check the signal strength in
the "Auto Scan" menu, correct alignment
of your antenna
On-Screen Error Message
Antenna cable not connected
Check connection and correct;
"Searching for signal"
or not tight;
LNB defective;
Change LNB;
incorrect position of the
Check position and correct,
satellite antenna;
Check the signal strength in
the "Auto Scan" menu
On-Screen Error Message
Satellite not yet set
Scan of in "Automatic scanning"
"Channel data
or "Manual scanning" menu
does not exist."
On-Screen Error Messages: Smartcard:
(depend on model)
"Please check the - not plugged in correctly; Check the Smartcard.
Smartcard"; - not plugged in. "Insert the Smartcard."
"Please insert the
Smartcard".
The device, packaging material (e.g. Styrofoam) and the batteries
must never be disposed of with household refuse.
Please obtain appropriate information about the regulations in your community,
and dispose of all refuse in accordance with regulations at the separate
locations provided.
DISPOSAL
TECHNICAL SPECIFICATIONS
DSR9400-GB_4.0 6/24/03 1:37 PM Page 30
