Samsung CA17J Series Service Manual Download Page 48 | Manualshive

Page: 48 / 67

background image

CONFIDENTIAL

5 Troubleshooting

5-12

CA17K*/CA17J*

5-1-20 User Control Failure

Does the DC level change at

Pin 36 of IC201 when you

push the button S/W?

Yes

Check the button.

(SW201 ~ SW204)

No

Check IC201, CN2 and CN206.

RL601 operation is right?

Q601 base input is right?

Check 13V Line.

Check and replace Q601.

No

No

Yes

Check D-coil and TH601.

Yes

IC201 Pin 4 output is right?

Check and replace IC201.

Yes

No

Done.

Check degaussing connector.

5-1-21 Degaussing Failure

«
...
46
47
48
49
50
...
»

Summary of Contents for CA17J Series




































































Reviews:

No comments

Related manuals for CA17J Series

ThinkVision L191p

Brand: IBM Pages: 38

Brand: IBM Pages: 18

51MP392H - 51" Widescreen Hd Ready Tv

Brand: Magnavox Pages: 7

Brand: Rae Pages: 4

Brand: Daktronics Pages: 70

ThinkVision L190N

Brand: IBM Pages: 42

Brand: Unicont SPb Pages: 13

Brand: I-Tech Pages: 50

Brand: Collins Pages: 23

Brand: A1 Touch Pages: 14

Brand: ViewSonic Pages: 2

DINAMAP PRO 100

Brand: Critikon Pages: 77

BABYTOUCH 29763Z

Brand: Summer Pages: 12

Brand: Beurer medical Pages: 120

Brand: Kettler Pages: 28

Brand: ViewSonic Pages: 25

Marquee-Lite PLUS 3225

Brand: Pro Lite Pages: 10

Brand: Well Health Pages: 156

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands