Samsung CA17J Series Service Manual Download Page 46

Page: 46 / 67

CONFIDENTIAL

5 Troubleshooting

5-10

CA17K*/CA17J*

5-1-17 No Highlight Zone (CA17J* Only)

IC101 Pin 2, 4 and 6

inputs are right?

IC101 Pin 20, 22 and 24

outputs are right?

Check +5V IC101 pin 1, 23.

Yes

IC101 Pin 12, 13 are right?

C Data / Clock Line)

Check Micom (IC201)
I

C Data / Clock Line.

IC101 Pin 14, 15 and

V_FLB, CLAMP

waveforms are right?

Check CLAMP, V_FLB waveforms.

Done.

19 20

WAVEFORMS

1.00 V (IC101, #20, 22, 24)

1.00 V (IC101, #14)

1.00 V (IC101, #15)

5-1-18 Micom Failure

IC201 Pin 11 input voltage is 5V?

IC201 Pin 13 and 14

inputs are right?

Check C202, C203 and X201.

Yes

Check IC604.

IC201 Pin 18 input is right?

Check IC605 and 5V.

Yes

All in/output values are right?

Replace IC201.

Yes

Done.

WAVEFORMS

1.00 V (IC201, #13, 14)

CH1 P-P = 1.00 V

CH1 RMS = 2.108V

Summary of Contents for CA17J Series




































































Search results

Summary of Contents for CA17J Series

Reviews:

Related manuals for CA17J Series

Brands by name

Popular brands

Samsung CA17J Series, Service Manual

Search results

Summary of Contents for CA17J Series

Reviews:

Related manuals for CA17J Series

Brands by name

Popular brands