SaMASZ DUO 1200 S Operator'S Manual Download Page 21 | Manualshive

Page: 21 / 25

SaMASZ DUO 1200 S Operator'S Manual Download Page 21

Instruction manual

Fodder wagons OptiFEED

19

The electronic control panel is equipped with a large, clear display to show messages

regarding the machine's current work mode and on-screen buttons for individual functions. Below is
detailed description of the control panel “push and hold” buttons.

Control panel ON/OFF button.

Belt conveyor control PCV in mixer feeders equipped with belt
conveyors.

Leftward operation.

Belt conveyor control PCV in mixer feeders equipped with belt
conveyors.

Rightward operation.

Discharge window control – OPEN.

Discharge window control – CLOSE.

Hydraulic counter-knife control – in mixer feeders equipped with
hydraulic counter-knife.

Knife OUT.

Hydraulic counter-knife control – in mixer feeders equipped with
hydraulic counter-knife.

Knife IN.

Support leg control – in mixer feeders equipped with hydraulic support
leg.

Support leg – FOLD.

Support leg control – in mixer feeders equipped with hydraulic support
leg.

Support leg – UNFOLD.

«
...
19
20
21
22
23
...
»

Summary of Contents for DUO 1200 S


























Reviews:

No comments