manualshive.com logo in svg

Salamander Pumps RP100PT, Installation And Warranty Manual, Page: 8 / 29

Share
Download
Salamander Pumps RP100PT Installation And Warranty Manual Download Page 8

5

Pre-installation

Installation

PumpWise guidelines

General specification

Trouble shooting

PumpWise and warranty

The plumbing installation must comply 

with “The Water Supply (Water Fittings) 

Regulations 1999” and “BS EN 806-

4:2010” buildings regulations.

5  Electrical requirements

The pump must be connected to the 

electrical supply using the mains cable 

with the attached plug. This plug must be 

connected to an accessible socket that has 

been installed in compliance with BS 7671 

(I.E.T. Wiring Regulations). The plug must be 

accessible at all times.
The pump must not be installed in a 

bathroom unless it is installed in an 

enclosed space accessible only with the use 
of a tool.
If the supply cord is damaged, it must be 

replaced by the manufacturer, its service 

agent or similarly qualified person in order 

but they must NOT be twisted or bent more 
than 35º (this invalidates the warranty). 
See Figure 5 above.

Each single pump is supplied with two 

couplers; one angled and one straight.  

The angled coupler should be attached to 

the pump inlet (on the side) and the straight 

coupler should be attached to the pump 

outlet (on the top).
Each twin pump is supplied with four 

couplers; two angled and two straight.
For all pumps, the inlets are on the side of 

the pump and the outlets are on the top of 

the pump.
The AV couplers MUST only be tightened 

to finger tight plus one quarter turn. 

Mechanical tools must NOT be used to 

tighten coupler nuts as this may cause 

damage which will invalidate your warranty.

4  General plumbing

The installation must comply with the 

relevant requirements or local by-laws.
The pump MUST be mounted upright (shaft 

horizontal, not screwed down).
Jointing compounds, Boss White, hemp 

or steel wool MUST NOT be used. Solder 

fluxes must not come into contact with the 

pump or AV couplers.
The maximum static head should be 10m 

(equivalent to 100kPa/1.0 bar pressure) 

with the exception of the RP50TU where 

the maximum static head should be 5m 

(equivalent to 50kPa/0.5bar pressure)

Pump

Fuse

RP55PS, RP80PS and RP120PS

3 amp

RP50PT

3 amp

RP75PT and RP100PT

5 amp

RP55SU, RP80SU, RP120SU and 

RP50TU

3 amp

RP75TU and RP100TU

5 amp

We recommend that the pump is run 

for at least 5 minutes every 4 weeks in 

order to exercise all working parts. 

Summary of Contents for RP100PT






























Reviews:

No comments