manualshive.com logo in svg

Salamander Pumps RP100PT, Installation And Warranty Manual, Page: 18 / 29

Share
Download
Salamander Pumps RP100PT Installation And Warranty Manual Download Page 18

15

Pre-installation

Installation

PumpWise guidelines

General specification

Trouble shooting

PumpWise and warranty

Figure 26: Anti-gravity loop (AGL)

MAX

60°C

Outlets

Inlet

Min

600mm

Usable capacity

minimum 50 gallons

per bathroom

Vent and other 

services

Non-return valve

hot outlet only

except ESP pumps

Air vents, both

hot and cold

No Stop Essex Flange

MUST be used with an 

anti gravity loop at least

250mm in depth 

C

H

Fig 23 Anti gravity loops

OLD STYLE DO NOT USED

Vent and 

other

services

Inlet

No Stop Essex Flange

MUST be used with an

anti-gravity loop at least

250mm in depth

Cold water storage

H

C

Air vents, 

both hot 

and cold

MAX

60˚C

600mm or

less possible

negative head

Outlet

Outlet

Non-return 

valve hot 

outlet only

except ESP 

pumps

Combi boilers and water heaters

As these appliances are invariably supplied 

directly from the cold mains – they are not 

normally suitable for booster pumps. The 

exceptions are featured in Figure 14 on  

page 10.

Figure 27: Combi boilers

Combi 

boiler

Incoming

water main

C

H

Fig 24 Combi boilers

OLD STYLE DO NOT USED

Incoming

water main

WRONG

Combi

boiler

C

H

Horizontal cylinders

As horizontal (torpedo) cylinders are 

problematic for boosted systems consult 

PumpWise for guidance and correct use of 

an approved top entry flange.

Use any of the 

approved top 

entry flanges

Usable capacity

minimum 50 galls

per bathroom

C

MAX

65°C

H

Fig 25 Horizontal cylinders

OLD STYLE DO NOT USED

Use any of the 

approved top 

entry flanges

Usable capacity

minimum 50 galls

per bathroom

MAX

60˚C

C

H

Approved flanges (cylinders)

The 22mm No Stop Essex and the other 

approved top entry flanges with extension 

pipes into the cylinder represent the best 

known means of ensuring minimal aeration 

of the hot supply water to the pump. The No 

Stop Essex flange is in all circumstances 

the best option.

S flange

Complete with compression ‘pump’ and 

‘open vent’ connections. Also supplied 

with an adaptor to connect to 1’’ ‘male’ and 

‘female’ top entry cylinders.

Figure 29: S flange

Figure 28: Horizontal cylinders

Fig 29 S Flange

HOT WATER

CYLINDER

To pump

To vent

S flange

York flange

These may be used in systems where the 

hot water requirement is less than 20 

Litres per minute.

Summary of Contents for RP100PT






























Reviews:

No comments