manualshive.com logo in svg

Salamander Pumps RP100PT, Installation And Warranty Manual, Page: 16 / 29

Share
Download
Salamander Pumps RP100PT Installation And Warranty Manual Download Page 16

13

Pre-installation

Installation

PumpWise guidelines

General specification

Trouble shooting

PumpWise and warranty

Figure 21

Pre-plumbed direct or indirect 

combination units

These are purpose-made units typically for 

use in multiple flat developments, usually in 

towns and cities where it is advantageous 

and desirable to provide the occupants with 

completely independent hot and cold  

water services.
In these systems the ideal pump is an 

RP50/75 TU. For alternative types of 

combination units see Elson, Figure 23 and 

Fortic (type), see Figure 24.

Cold mains

ball valve

Immersion heater

and an indirect

connection to a

boiler

Lid

H

C

Cold

water

storage

MAX

65°C

OLD STYLE DO NOT USED

Fig 19  Pre plumped

MAX

60˚C

Cold mains

ball valve

Cold

water

storage

Immersion heater

and an indirect

connection to a

boiler

Lid

H

C

Figure 22: Pre-plumbed direct or indirect 
combination units

Elson (type) tanks

In these systems it is important to ensure 

the hot and cold water storage capacity is 

adequate for the type of pump to be used. 
The refill ball valve on the small cold tank 

which refills the hot tank is correctly set to 

prevent aeration of the hot supply water to 

the pump.

Figure 23: Elson (type) tanks

Fortic (type) tanks and  

pre-assembled units

Typically used in very small flats and 

houses. Not usually with sufficient water 

capacity of cold water for pumped systems.

Figure 24: Fortic (type) tanks and  

pre-assembled units

Small cold water

storage tank

Hot outlet

OLD STYLE DO NOT USED

Fig 21 Fortic tanks

Cold

tank

Hot

tank

Refill ball valves

Immersion

heaters

C

H

Summary of Contents for RP100PT






























Reviews:

No comments